Simpson Strong-Tie

The Simpson Strong-Tie CJT6ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT6ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT6ZS short (2-3/4") pins can be used with 3-1/8" Glulam Beams, 4x sawn lumber or 3-1/2" PSL. Minimum Joist Size: Douglas Fir - 4 x 12 Glulam Beam - 3-1/8" x 12" PSL - 3-1/2 x...

Simpson Strong-Tie ECCQ44-SDS2.5HDG Hot Dipped Galvanized End Column Caps provide a high capacity connection between a 4x beam and a 4x post. ECCQ44-SDS2.5HDG End Column Caps should be used when the...

Simpson Strong-Tie ECCQ44-SDS2.5HDG Hot Dipped Galvanized End Column Caps provide a high capacity connection between a 4x beam and a 4x post. ECCQ44-SDS2.5HDG End Column Caps should be used when the beam ends at the post. Each ECCQ44-SDS2.5HDG End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Hot Dipped Galvanized coating provides corrosion resistance when required. Material: 7 gauge Finish: Hot...

The Simpson CBSQ46-SDS2HDG (for 3-1/2" x 5-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post...

The Simpson CBSQ46-SDS2HDG (for 3-1/2" x 5-1/2" post) column bases include (14) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Hot Dipped Galvanized for additional corrosion resistance. Easier Installation Higher Loads Hot Dipped Galvanized Column Size: 4 x 6 Nominal (3-1/2" x 5-1/2") Base: 12 Ga. (3-9/16" x 5-5/16") Strap: 10 Ga. x 3"...

Simpson Strong-Tie LSTA30 18 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. LSTA series straps are designed to be used on the edge of 2x...

Simpson Strong-Tie LSTA30 18 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. LSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a LSTA strap that requires bending the strap can only be bent one time. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 30" (Length) Fasteners: (22) 10d Nails (22) SD9 x 1-1/2" Screws...

Simpson Strong-Tie ST2122 20-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of...

Simpson Strong-Tie ST2122 20-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of applications. Material: 20 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/16" (Wide) x 12-13/16" (Length) Fastener Options: (16) 16d Nails (16) SD10 x 1-1/2" Screws ST2122 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating...

Head is Painted Sienna! The Simpson Strong-Tie 3" x .120" Sienna Ring Shank Type 304 Stainless Steel Coil Nail is the best solution to protect your considerable investment in fine wood siding from...

Head is Painted Sienna! The Simpson Strong-Tie 3" x .120" Sienna Ring Shank Type 304 Stainless Steel Coil Nail is the best solution to protect your considerable investment in fine wood siding from hard-to-remove stains and streaks with stainless steel wire coil nails. Chose from four colors or unpainted to match your siding. 1,800 nails per box Head Color - Sienna Type 304 stainless steel 15° collated angle Checker pattern on heads blends with wood grain, reduces glare from sunlight and...

The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. Simpson Strong-Drive SD10212 #10 x 2-1/2"...

The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. Simpson Strong-Drive SD10212 #10 x 2-1/2" structural connector screws are approved to replace nails in certain Simpson Strong-Tie Connectors. The advantages of using screws can be ease of installation in tight spots and less vibration when installing connectors during remodel projects. The shank of the SD9112 screws are designed to easily fit...

The Simpson Strong Tie GH48-6 Girder Hangers is used to connect a 4 x 8 girder to a 6" foundation wall using 2x sill plate. 1-1/2 clearance hole can accommodate either rebar or an anchor bolt if...

The Simpson Strong Tie GH48-6 Girder Hangers is used to connect a 4 x 8 girder to a 6" foundation wall using 2x sill plate. 1-1/2 clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 5-5/8" (H) x 6-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH48-6 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...

The Simpson Strong-Tie SUR26 Skewed Right 2 x 6/8 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate...

The Simpson Strong-Tie SUR26 Skewed Right 2 x 6/8 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 6/8 joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 5" (Height) x 1-1/8" (Outside Flange) x 1-5/16" (Inside Flange) Fastener Options : (6) .162" x 3-1/2" 16d Nails (Face) (6) .148" x...

The Simpson Strong-Tie® Strong-Drive® SDWH19800DB 8" screw is ideal for structural and general-purpose fastening applications where a hex-head drive is preferred. This 0.195" diameter...

The Simpson Strong-Tie® Strong-Drive® SDWH19800DB 8" screw is ideal for structural and general-purpose fastening applications where a hex-head drive is preferred. This 0.195" diameter fastener requires less torque to install than comparable fasteners, making it easier to drive; while the corrosion-resistant coating makes it suitable for many interior and exterior applications. The large hex washer head of the SDWH19800DB 8" screw creates an excellent bearing area for a secure...

The Simpson Strong-Tie® Strong-Drive® SDWS22600DB .220" x 6" wood screw is specifically designed for structural wood-to-wood applications and is also ideal for a wide variety of projects...

The Simpson Strong-Tie® Strong-Drive® SDWS22600DB .220" x 6" wood screw is specifically designed for structural wood-to-wood applications and is also ideal for a wide variety of projects where a high-strength attachment is needed. The 0.220" diameter of the SDWS22600DB 6" wood screw requires less torque to install than comparable fasteners, making it easier to drive. The Double-Barrier Coating corrosion-resistant coating makes it suitable for many interior and exterior applications....

The Simpson Strong-Tie HD9B Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown uses the same design...

The Simpson Strong-Tie HD9B Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown uses the same design as the HDQ8-SDS2.5 holdown that is proven to greatly reduce deflection while under load. All the HDB style holdown anchors are designed to provide loads for intermediate-load-range shearwalls, braced wall panels and lateral applications. The HD9B must be connected to a minimum of 3-1/2" of...

Simpson Strong-Tie EPB46 allows you to install an elevated 4 x 6 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 6 post to stay above most standing water thus delaying...

Simpson Strong-Tie EPB46 allows you to install an elevated 4 x 6 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 6 post to stay above most standing water thus delaying any deterioration that will happen over time. EPB Post Bases do not provide enough resistance to stop a post from rotating so they should not be used in applications with no top connection such as fences and unbraced carports. Finish: Simpson Gray Paint Pipe Size: 1-1/16" OD x 8" Length Base Size:...

Simpson Strong-Tie 16DHDG-R 3-1/2" x .162" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 40 nails in the 1 lb....

Simpson Strong-Tie 16DHDG-R 3-1/2" x .162" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 40 nails in the 1 lb. pack. The nails are hot dipped galvanized, providing medium corrosion protection. 16DHDG-R Information and Data Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average coating...

The Simpson AC6Z ZMax® Split Post Caps allow you to install the cap after the 6x post and 6x beam are set. ZMax® coating provides additional corrosion resistance when applicable. Material:...

The Simpson AC6Z ZMax® Split Post Caps allow you to install the cap after the 6x post and 6x beam are set. ZMax® coating provides additional corrosion resistance when applicable. Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 5-1/2" (W) x 8-1/2" (L) Fastener Options: Beam...(8) .162 x 3-1/2" Nails (Min) Beam...(14) .162 x 3-1/2" Nails (Max) Post...(8) .162 x 3-1/2" Nails (Min) Post...(14) .162 x 3-1/2" Nails (Max) Post and Beam...(28) SD10 x 1-1/2" (Max) AC6Z Information...

Simpson Strong-Tie LUC26Z ZMax® 2 x 6/8Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC26Z also provides cleaner lines for exposed conditions such as...

Simpson Strong-Tie LUC26Z ZMax® 2 x 6/8Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC26Z also provides cleaner lines for exposed conditions such as overhead decks. Material: 18 Gauge Finish: G-185 ZMax® Dimensions: 1-9/16" (Wide) x 4-3/4" (Height) x 1-3/4" (Seat Depth) Fastener Options: Fastener Options: (6) .162 x 3-1/2" 16d Nails (Header) (4) .148 x 1-1/2" 10d Nails (Joist) Strong Drive® SD9112 #9 x 1-1/2" Structural Screws may be...

Simpson Strong Tie face mount HU9 Composite Lumber Hanger is designed for hanging 1-3/4" x 9-1/2" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load...

Simpson Strong Tie face mount HU9 Composite Lumber Hanger is designed for hanging 1-3/4" x 9-1/2" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load value. Material: 14 gauge Finish: Standard G90 Galvanized- Dimensions: 1-13/16" (Wide) x 9-5/16" (Height) x 2-1/2" (Seat Depth) Fastener Options: (18) 16d Nails (Header-Min) (6) 10d Nails (Joist-Min) (24) 16d Nails (Header-Max) (10) 10d Nails (Joist-Max) HU9 Information and Installation Instructions....

Simpson Strong-Tie HDU4-SDS2.5 Hot Dipped Galvanized Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with...

Simpson Strong-Tie HDU4-SDS2.5 Hot Dipped Galvanized Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (10) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Hot Dipped Galvanized holdowns should be used when the application in either...

The 1-1/4" wide x 16" long LTS16 Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist...

The 1-1/4" wide x 16" long LTS16 Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist straps have a 2" bend section that eliminates interference at the transition points between the two members. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 16" (Length) Fasteners: 10d or 10d x 1-1/2" depending on load value required and depth of receiving member (See...

The Simpson BC46Z ZMax® Post Caps allow you to create a light duty connection between a 4 x 6 nominal post and 4x nominal beam. The ZMax® coating provide corrosion resistance when caps are...

The Simpson BC46Z ZMax® Post Caps allow you to create a light duty connection between a 4 x 6 nominal post and 4x nominal beam. The ZMax® coating provide corrosion resistance when caps are installed in exposed locations. Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 3-9/16" (W) x 5-1/2" (L) Fastener Options: (18) 16d BC46Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653...

Simpson Strong-Tie 16D5HDG-R 3-1/2" x .162" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 200 nails in the 5 lb....

Simpson Strong-Tie 16D5HDG-R 3-1/2" x .162" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 200 nails in the 5 lb. pack. The nails are hot dipped galvanized, providing medium corrosion protection. 16D5HDG-R Information and Data Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average coating...

The S/HDU9 Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HDU9 holdown...

The S/HDU9 Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HDU9 holdown combines performance with ease of installation using #14 screws self-drilling tapping screws thus saving time and labor.. The pre-deflected geometry virtually eliminates material stretch, resulting in low deflection under load. Foundation Anchor Diameter: 7/8" Fasteners (Not Included): (18) #14 Screws...

Simpson Strong-Tie EPB46HDG allows you to install an elevated 4 x 6 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 6 post to stay above most standing water thus...

Simpson Strong-Tie EPB46HDG allows you to install an elevated 4 x 6 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 6 post to stay above most standing water thus delaying any deterioration that will happen over time. EPB Post Bases do not provide enough resistance to stop a post from rotating so they should not be used in applications with no top connection such as fences and unbraced carports. Hot Dip Galvanizing provides corrosion resistance for additional...

Simpson Strong-Tie MASAP anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAP is not only quick to install they also eliminate the...

Simpson Strong-Tie MASAP anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAP is not only quick to install they also eliminate the added cost of installing a bearing plate on the anchor bolt. This MASAP version is used for installation on panelized forms. Attaches easily to the concrete form for quick installation Lays flat on the panelized form so there is no anchor bolt to finish around No labor costs involved in drilling...