Additional Hangers

The Simpson Strong-Tie CJT3ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT3ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT3ZS short (2-3/4") pins can be used with 3-1/8" Glulam Beams, 4x sawn lumber or 3-1/2" PSL. Minimum Joist Size: Douglas Fir - 4 x 6 Glulam Beam - 3-1/8" x 7-1/2" PSL - 3-1/2 x...

The Simpson Strong Tie GH46-6 Girder Hangers is used to connect a 4 x 6 girder to a 6" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...

The Simpson Strong Tie GH46-6 Girder Hangers is used to connect a 4 x 6 girder to a 6" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 3-7/8" (H) x 6-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-6 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...

The Simpson Strong-Tie CJT3ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT3ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT3ZL long (4-3/4") pins can be used with 5-1/8" Glulam Beams or 6x sawn lumber. Minimum Joist Size: Douglas Fir - 6 x 8 Glulam Beam - 5-1/8" x 7-1/2" Material: 12 Gauge Finish:...

The Simpson Strong-Tie CJT4ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT4ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT4ZS short (2-3/4") pins can be used with 3-1/8" Glulam Beams, 4x sawn lumber or 3-1/2" PSL. Minimum Joist Size: Douglas Fir - 4 x 10 Glulam Beam - 3-1/8" x 9" PSL - 3-1/2 x...

The Simpson Strong Tie GH46-8 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...

The Simpson Strong Tie GH46-8 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 3-7/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-8 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...

The Simpson Strong-Tie CJT4ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT4ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT4ZL long (4-3/4") pins can be used with 5-1/8" Glulam Beams or 6x sawn lumber. Minimum Joist Size: Douglas Fir - 6 x 10 Glulam Beam - 5-1/8" x 9" Material: 12 Gauge Finish:...

The Simpson Strong-Tie CJT5ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or...

The Simpson Strong-Tie CJT5ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT5ZS short (2-3/4") pins can be used with 3-1/8" Glulam Beams, 4x sawn lumber or 3-1/2" PSL. Minimum Joist Size: Douglas Fir - 4 x 12 Glulam Beam - 3-1/8" x 10-1/2"...

The Simpson Strong Tie GH46-8/3 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 3x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...

The Simpson Strong Tie GH46-8/3 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 3x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 2-7/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-8/3 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...

The Simpson Strong-Tie CJT5ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT5ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT5ZL long (4-3/4") pins can be used with 5-1/8" Glulam Beams or 6x sawn lumber. Minimum Joist Size: Douglas Fir - 6 x 12 Glulam Beam - 5-1/8" x 10-1/2" Material: 12 Gauge Finish:...

The Simpson Strong-Tie CJT6ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT6ZS is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT6ZS short (2-3/4") pins can be used with 3-1/8" Glulam Beams, 4x sawn lumber or 3-1/2" PSL. Minimum Joist Size: Douglas Fir - 4 x 12 Glulam Beam - 3-1/8" x 12" PSL - 3-1/2 x...

The Simpson Strong Tie GH48-6 Girder Hangers is used to connect a 4 x 8 girder to a 6" foundation wall using 2x sill plate. 1-1/2 clearance hole can accommodate either rebar or an anchor bolt if...

The Simpson Strong Tie GH48-6 Girder Hangers is used to connect a 4 x 8 girder to a 6" foundation wall using 2x sill plate. 1-1/2 clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 5-5/8" (H) x 6-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH48-6 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...

The Simpson Strong-Tie CJT6ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT6ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT6ZL long (4-3/4") pins can be used with 5-1/8" Glulam Beams or 6x sawn lumber. Minimum Joist Size: Douglas Fir - 6 x 12 Glulam Beam - 5-1/8" x 12" Material: 12 Gauge Finish:...

The Simpson Strong Tie GH48-8 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...

The Simpson Strong Tie GH48-8 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 5-5/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH48-8 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...

The Simpson Strong-Tie HCJTZ is a heavy concealed connector used to provide a secure connection between a large wood beam to a wood post with no visible hardware. It can be installed three ways:...

The Simpson Strong-Tie HCJTZ is a heavy concealed connector used to provide a secure connection between a large wood beam to a wood post with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie HCJTZ with 3/4" x 4-3/4" pins can be used with a minimum beam size of 5-1/8" x 15". Minimum Beam Size: 5-1/8" x 15" Material: 10 Gauge Finish:...

The Simpson Strong Tie GH48-8/3 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 3x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...

The Simpson Strong Tie GH48-8/3 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 3x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 4-5/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH48-8/3 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...