Simpson Strong-Tie

The Simpson Strong-Tie PAB5-12 5/8" x 12" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features...

The Simpson Strong-Tie PAB5-12 5/8" x 12" Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department direct at 800-323-2999 for...

Simpson Strong-Tie MASAP anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAP is not only quick to install they also eliminate the...

Simpson Strong-Tie MASAP anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAP is not only quick to install they also eliminate the added cost of installing a bearing plate on the anchor bolt. This MASAP version is used for installation on panelized forms. Attaches easily to the concrete form for quick installation Lays flat on the panelized form so there is no anchor bolt to finish around No labor costs involved in drilling...

The Simpson Strong-Tie DSVR4R5LB #10 x 4" Deck Drive™ Redwood Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip,...

The Simpson Strong-Tie DSVR4R5LB #10 x 4" Deck Drive™ Redwood Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSV is ideally suited to be driven and countersunk into today’s wood deck boards. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth lumber. Also DSV screws are available in collated strips for use in the Quik Drive® auto-feed screw driving system....

Simpson Strong-Tie PDPAWL-200 Zinc Plated Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel PDPA pin...

Simpson Strong-Tie PDPAWL-200 Zinc Plated Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel PDPA pin preassembled with a 1″ washer that provides additional bearing surface for enhanced upload resistance. Length: 2" Head Diameter: .300" Shank Diameter: .157" Coating: Standard G90 Zinc PDPAWL Series Fasteners Tension and Shear Loads in Normal Weight Concrete PAT Fastener MSDS Standard G90 Zinc...

Save by Purchasing a Quantity of 500 SSTB20 Bolts! The Simpson Strong-Tie SSTB20 (5/8" Diameter by 21-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall...

Save by Purchasing a Quantity of 500 SSTB20 Bolts! The Simpson Strong-Tie SSTB20 (5/8" Diameter by 21-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 21-5/8" Minimum...

Simpson Strong-Tie 16D5HDG-R 3-1/2" x .162" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 200 nails in the 5 lb....

Simpson Strong-Tie 16D5HDG-R 3-1/2" x .162" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 200 nails in the 5 lb. pack. The nails are hot dipped galvanized, providing medium corrosion protection. 16D5HDG-R Information and Data Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average coating...

Simpson Strong-Tie LUC26SS Type 316L Stainless Steel 2 x 6/8Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC26SS also provides cleaner lines for exposed...

Simpson Strong-Tie LUC26SS Type 316L Stainless Steel 2 x 6/8Concealed Flange Joist Hanger are ideal for end of ledger, header or post conditions. The LUC26SS also provides cleaner lines for exposed conditions such as overhead decks. Material: 18 Gauge Finish: Type 316L Stainless Steel Dimensions: 1-9/16" (Wide) x 4-3/4" (Height) x 1-3/4" (Seat Depth) Fastener Options: (6) .162 x 3-1/2" 16d Nails (Header) (4) .148 x 1-1/2" 10d Nails (Joist) Strong Drive® SD9112 #9 x 1-1/2" Structural Screws...

Simpson Strong Tie LUS26Z ZMax® 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It...

Simpson Strong Tie LUS26Z ZMax® 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS26Z hangers are also approved for installation with SD9 Structural Screws. Material: 18 gauge Finish: ZMax® G-185 Galvanized Dimensions: 1-9/16" (Wide) x 4-3/4" (Height) x 1-3/4" (Seat...

The Simpson AC6RZ ZMax® Split Post Caps allow you to install the cap after the rough 6x post and rough 6x beam are set. ZMax® coating provides additional corrosion resistance when...

The Simpson AC6RZ ZMax® Split Post Caps allow you to install the cap after the rough 6x post and rough 6x beam are set. ZMax® coating provides additional corrosion resistance when applicable. Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 6" (W) x 9" (L) Fastener Options: Beam...(8) .162 x 3-1/2" Nails (Min) Beam...(14) .162 x 3-1/2" Nails (Max) Post...(8) .162 x 3-1/2" Nails (Min) Post...(14) .162 x 3-1/2" Nails (Max) Post and Beam...(28) SD10 x 1-1/2" (Max) AC6RZ...

The Simpson BC46Z ZMax® Post Caps allow you to create a light duty connection between a 4 x 6 nominal post and 4x nominal beam. The ZMax® coating provide corrosion resistance when caps are...

The Simpson BC46Z ZMax® Post Caps allow you to create a light duty connection between a 4 x 6 nominal post and 4x nominal beam. The ZMax® coating provide corrosion resistance when caps are installed in exposed locations. Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 3-9/16" (W) x 5-1/2" (L) Fastener Options: (18) 16d BC46Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653...

Simpson Strong-Tie CCO5 1/4 End Column Caps with no post straps provides a high capacity connection between a 5-1/8" wide beam and a steel post. The CCO5 1/4 Column Caps comes with no coating to...

Simpson Strong-Tie CCO5 1/4 End Column Caps with no post straps provides a high capacity connection between a 5-1/8" wide beam and a steel post. The CCO5 1/4 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 3 gauge Finish: No Coating Dimensions: 5-1/8"...

Simpson Strong-Tie CCQ44-SDS2.5HDG Hot Dipped Galvanized Column Caps provide a high capacity connection between a 4x beam and a 4x post. CCQ44-SDS2.5HDG Column Caps should be used when the beam...

Simpson Strong-Tie CCQ44-SDS2.5HDG Hot Dipped Galvanized Column Caps provide a high capacity connection between a 4x beam and a 4x post. CCQ44-SDS2.5HDG Column Caps should be used when the beam extends through the post. Each CCQ44-SDS2.5HDG Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Hot Dipped Galvanized coating provides corrosion resistance when required. Material: 7 gauge Finish: Hot Dipped...

The Simpson Strong-Tie BC60Z ZMax® Half Base is an economical way to attach a nominal 6 x 6 post to a wood subfloor or bottom plate. ZMax Corrosion Protection provides additional resistance to...

The Simpson Strong-Tie BC60Z ZMax® Half Base is an economical way to attach a nominal 6 x 6 post to a wood subfloor or bottom plate. ZMax Corrosion Protection provides additional resistance to corrosive conditions. Base Material: 18 Gauge Dimensions: (W) 5-1/2" x (L) 5-1/2" x (H) 3" Finish: ZMax G-185 Coating Fastener Options: (10) 16d Nails BC60Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM...

The Simpson Strong-Tie ABU66RZ with ZMax® Corrosion Resistance is an adjustable post base for rough size 6 x 6 post offers moisture protection and a finished hardware appearance. The ABU66RZ...

The Simpson Strong-Tie ABU66RZ with ZMax® Corrosion Resistance is an adjustable post base for rough size 6 x 6 post offers moisture protection and a finished hardware appearance. The ABU66RZ features 1" standoff height above concrete floors which is code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Base Material: 12 Gauge Strap Material: 10 Gauge Dimensions: (W)...

Simpson Strong-Tie CC46HDG Hot Dipped Galvanized Column Caps provide a high capacity connection between a 4x wide beam and a 6x post. CC46HDG Column Caps should be used when the 4x beam extends...

Simpson Strong-Tie CC46HDG Hot Dipped Galvanized Column Caps provide a high capacity connection between a 4x wide beam and a 6x post. CC46HDG Column Caps should be used when the 4x beam extends through the 6x post. Please Note: This column cap is also available in powder coat as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 7 gauge Finish: Hot Dipped Galvanized Dimensions: 3-5/8" (Beam) x 5-1/2" (Post) x 11" (Length) Fasteners: (4) 5/8" Machine...

The Simpson Strong-Tie LTTP2 Light Tension Tie is designed for wood joist attachments to concrete or masonry. The LTTP2 features an extruded anchor bolt hole to accommodate 1/2", 5/8" and 3/4" bolt...

The Simpson Strong-Tie LTTP2 Light Tension Tie is designed for wood joist attachments to concrete or masonry. The LTTP2 features an extruded anchor bolt hole to accommodate 1/2", 5/8" and 3/4" bolt diameters. It also features two separate nailing patterns: obround holes spaced 3" apart for I-joist purlins and square holes spaced to accommodate the narrow face of 2x solid-sawn purlins. The LTTP2 may be installed vertically on the wide face of a minimum 2x4 stud for holdown applications and can...

The Simpson Strong-Tie HD9BHDG Hot Dipped Galvanized Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This...

The Simpson Strong-Tie HD9BHDG Hot Dipped Galvanized Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown uses the same design as the HDQ8-SDS2.5 holdown that is proven to greatly reduce deflection while under load. All the HDB style holdown anchors are designed to provide loads for intermediate-load-range shearwalls, braced wall panels and lateral applications. The HD9B must be connected to a...

Simpson Strong-Tie PBS66HDG Hot Dipped Galvanized Standoff Post Bases are used to connect a 6 x 6 (5-1/2" x 5-1/2") to a concrete slab or pier. The 1" standoff keeps the post off the concrete which...

Simpson Strong-Tie PBS66HDG Hot Dipped Galvanized Standoff Post Bases are used to connect a 6 x 6 (5-1/2" x 5-1/2") to a concrete slab or pier. The 1" standoff keeps the post off the concrete which reduces the chance of decay over time. Hot dipped galvanizing provides and additional layer of protection from deterioration due to weather. Finish: Hot Dipped Galvanized Base Material: 12 Gauge Strap Material: 14 Gauge Fastener Options: (14) 16d (2) 1/2" Machine Bolts Additional PBS66HDG...

The S/HDU9 Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HDU9 holdown...

The S/HDU9 Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HDU9 holdown combines performance with ease of installation using #14 screws self-drilling tapping screws thus saving time and labor.. The pre-deflected geometry virtually eliminates material stretch, resulting in low deflection under load. Foundation Anchor Diameter: 7/8" Fasteners (Not Included): (18) #14 Screws...

Simpson Strong-Tie CB46HDG Hot Dipped Galvanized column bases are used to provide a connection of a 4 x 6 (3-1/2" x 5-1/2") post to concrete. The CB46HDG base is installed during the pouring of the...

Simpson Strong-Tie CB46HDG Hot Dipped Galvanized column bases are used to provide a connection of a 4 x 6 (3-1/2" x 5-1/2") post to concrete. The CB46HDG base is installed during the pouring of the concrete. Strap Material: 7 Ga. x 2" Wide Hot Dipped Galvanized Steel Base Material: 7 Ga Hot Dipped Galvanized (3-9/16" x 5-1/2") Fasteners: (2) 5/8" Machine Bolts CB46HDG Information and Installation Instructions Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the...

Simpson Strong-Tie EPB46HDG allows you to install an elevated 4 x 6 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 6 post to stay above most standing water thus...

Simpson Strong-Tie EPB46HDG allows you to install an elevated 4 x 6 post base from 1" to 2-1/2" above the concrete. This clearance allows the 4 x 6 post to stay above most standing water thus delaying any deterioration that will happen over time. EPB Post Bases do not provide enough resistance to stop a post from rotating so they should not be used in applications with no top connection such as fences and unbraced carports. Hot Dip Galvanizing provides corrosion resistance for additional...

Simpson Strong-Tie IUS2.06/9.5 is used to install 2" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator...

Simpson Strong-Tie IUS2.06/9.5 is used to install 2" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/8" (Wide) x 9-1/2" (Height) x 2" (Seat Depth) Fastener Options : (8) .148 x 3" Nails (Face) IUS2.06/9.5 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...

Simpson Strong Tie U26-2 Double 2 x 6/8 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements....

Simpson Strong Tie U26-2 Double 2 x 6/8 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 5" (Height) x 2" (Seat Depth) Fastener Options: (8) .162" x 3-1/2" 16d Nails (Header) (4) .148" x 3" 10d Nails (Joist) U26-2 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...

Simpson Strong Tie HU26-3 Triple 2 x 6/8 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...

Simpson Strong Tie HU26-3 Triple 2 x 6/8 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HU26-3 hangers include additional triangle holes that can be used to increase load values when required. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 4-11/16" (Wide) x 4-5/8" (Height) x 2-1/2" (Seat Depth)...