Login/Register
Shopping Cart
OR
The Simpson Strong-Tie ML26SS Stainless Steel 12 Gauge angle combines strength and versatility through the use of Strong-Drive SDS25112 Heavy-Duty Connector screws. Fastener holes are staggered to...
The Simpson Strong-Tie ML26SS Stainless Steel 12 Gauge angle combines strength and versatility through the use of Strong-Drive SDS25112 Heavy-Duty Connector screws. Fastener holes are staggered to minimize wood splitting and opposing hole patterns allow for back-to-back installation without fastener interference. Please Note: SDS screws are not included. Finish: Type 316L Stainless Steel Material: 12 Gauge Fasteners (Not Included): (8) SDS25112 Screws Dimensions: 6" Length x 2" (Flange Widths)...
The Simpson Strong-Tie THD37400H4SS Type 304 Stainless Steel 3/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...
The Simpson Strong-Tie THD37400H4SS Type 304 Stainless Steel 3/8" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...
The Simpson Strong-Tie BA1.81/11.88 Top Flange Hanger is designed for 1-3/4" x 11-7/8" engineered wood and solid sawn lumber applications. This top-flange hanger can carry medium loads with solid...
The Simpson Strong-Tie BA1.81/11.88 Top Flange Hanger is designed for 1-3/4" x 11-7/8" engineered wood and solid sawn lumber applications. This top-flange hanger can carry medium loads with solid sawn lumber and higher loads with engineered wood products. All BA hangers feature minimum nailing with positive-angle nailing (PAN) to target moderate load conditions and maximum nailing to support higher loads. Please Note: BA Hangers may be modified for slopes and/or skews up to 45°. The top...
The Simpson Strong-Tie ETB75S 3/4" Wire Brush is part of the Simpson wire brush system that is specifically designed for use with Simpson Strong-Tie® SET-3G™ and AT-3G™ adhesives to...
The Simpson Strong-Tie ETB75S 3/4" Wire Brush is part of the Simpson wire brush system that is specifically designed for use with Simpson Strong-Tie® SET-3G™ and AT-3G™ adhesives to permit proper hole cleaning with fewer brush strokes at embedments up to 20 times the anchor diameter. Useable Length: 5" Hole Size: 3/4" Anchor Diameter N/A Rebar Size #5 Explanation of "Stock" Availability Term Stock items are products we normally have available for immediate shipment either from...
The Simpson Strong-Tie ETB87S 7/8" Wire Brush is part of the Simpson wire brush system that is specifically designed for use with Simpson Strong-Tie® SET-3G™ and AT-3G™ adhesives to...
The Simpson Strong-Tie ETB87S 7/8" Wire Brush is part of the Simpson wire brush system that is specifically designed for use with Simpson Strong-Tie® SET-3G™ and AT-3G™ adhesives to permit proper hole cleaning with fewer brush strokes at embedments up to 20 times the anchor diameter. Useable Length: 5" Hole Size: 7/8" Anchor Diameter 3/4" Rebar Size #6 Explanation of "Stock" Availability Term Stock items are products we normally have available for immediate shipment either from...
Simpson Strong-Tie PDPAWL-200MG Mechanical Galvanized Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel...
Simpson Strong-Tie PDPAWL-200MG Mechanical Galvanized Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel PDPA pin preassembled with a 1″ washer that provides additional bearing surface for enhanced upload resistance. Length: 2" Head Diameter: .300" Shank Diameter: .157" Coating: Mechanical Galvanized PDPAWL Series Fasteners Tension and Shear Loads in Normal Weight Concrete PAT Fastener MSDS Mechanical...
Head is Painted Brown! The Simpson S10A325KJB 3-1/4" X .131" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted brown to match siding or decking...
Head is Painted Brown! The Simpson S10A325KJB 3-1/4" X .131" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted brown to match siding or decking when applicable. The countersunk casing head with a checker pattern on the head helps the nail blend with the wood grain. The annular ring shank increases pull-out resistance thus decreasing chances of the nails backing out over time. Type 304 stainless steel Countersunk casing head Ring Shank shank...
Simpson Strong-Tie ECCOQ6-SDS2.5 Weld-On End Column Cap with no post straps are designed to provide strong column-beam connections in end-of-beam and center beam applications on top of steel...
Simpson Strong-Tie ECCOQ6-SDS2.5 Weld-On End Column Cap with no post straps are designed to provide strong column-beam connections in end-of-beam and center beam applications on top of steel members. The column cap features a design without legs, enabling a field-welded attachment to steel columns and beams. The seat of the column cap provides additional surface area for bearing that extends beyond the side of the column. This helps distribute the load from the beam and provide support for the...
The Simpson Strong-Tie BA1.81/14 Top Flange Hanger is designed for 1-3/4" x 14" engineered wood and solid sawn lumber applications. This top-flange hanger can carry medium loads with solid sawn...
The Simpson Strong-Tie BA1.81/14 Top Flange Hanger is designed for 1-3/4" x 14" engineered wood and solid sawn lumber applications. This top-flange hanger can carry medium loads with solid sawn lumber and higher loads with engineered wood products. All BA hangers feature minimum nailing with positive-angle nailing (PAN) to target moderate load conditions and maximum nailing to support higher loads. Please Note: BA Hangers may be modified for slopes and/or skews up to 45°. The top flanges...
The Simpson MIU2.37/9 hanger is designed to hang 2-5/16" x 9-1/2" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU2.37/9 features...
The Simpson MIU2.37/9 hanger is designed to hang 2-5/16" x 9-1/2" joist in commercial, high-load and double I-joist applications without requiring web stiffeners. The MIU2.37/9 features positive-angle nailing (PAN) which minimizes splitting of the flanges while permitting time-saving nailing from a better angle. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. Material: 16 gauge Finish: Standard G90 Galvanized...
The Simpson T9A250MCN 2-1/2" x .148" Type 316 Stainless Steel Metal Connector Nails is designed to be used in 31/33 Degree Metal Connector Tools for installing Simpson Strong-Tie structural...
The Simpson T9A250MCN 2-1/2" x .148" Type 316 Stainless Steel Metal Connector Nails is designed to be used in 31/33 Degree Metal Connector Tools for installing Simpson Strong-Tie structural connectors like clips, straps, joist hangers and more. Since the installation of this product is usually done close to the face these nails have a paper tape as opposed to plastic that breaks off and poses a hazard to the eyes and face. Please Note: Consult your manufacturer's catalog to determine the...
Simpson Strong Tie HUC26-3 Triple 2 x 6/8 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HUC26-3 Triple 2 x 6/8 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC26-3 hangers include additional triangle holes that can be used to increase load values when required. Reversed flanges allow you to hang hoist flush at corners or any other location where outside flanges will not work. Material:...
Simpson Strong Tie HUCQ210-3Z-SDS ZMax®4-5/8" Wide Triple 2 x 10 Heavy Duty Joist Hangers come with the required SDS screws to reach the load values you require. HUCQ210-3Z-SDS hangers with...
Simpson Strong Tie HUCQ210-3Z-SDS ZMax®4-5/8" Wide Triple 2 x 10 Heavy Duty Joist Hangers come with the required SDS screws to reach the load values you require. HUCQ210-3Z-SDS hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: ZMax® G-185 Coating Dimensions: 4-5/8" (Wide) x 9" (Height) x 3" (Seat Depth) Included Fasteners: (12) SDS 1/4" x 2-1/2" Screws (Header) (6) SDS 1/4" x 2-1/2"...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.06/9.5 is used to install 2" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy...
Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.06/9.5 is used to install 2" x 9-1/2" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/8" (Wide) x 9-1/2" (Height) x 2" (Seat Depth) Fastener Options : (8) .148 x 3" Nails (Face) IUS2.06/9.5 Information and Installation...
The Simpson AC6SS Type 316L Stainless Steel Split Post Caps allow you to install the cap after the 6 x 6 post and 6x beam are set. Type 316L Stainless Steel protection provides additional corrosion...
The Simpson AC6SS Type 316L Stainless Steel Split Post Caps allow you to install the cap after the 6 x 6 post and 6x beam are set. Type 316L Stainless Steel protection provides additional corrosion resistance when application is in extreme corrosion situations. Material: 18 Gauge Finish: Type 316L Stainless Steel Dimensions 5-1/2" (W) x 8-1/2" (L) Fastener Options: Beam...(8) .162 x 3-1/2" Nails (Min) Beam...(14) .162 x 3-1/2" Nails (Max) Post...(8) .162 x 3-1/2" Nails (Min) Post...(14) .162 x...
The Simpson Strong-Tie TNT18214H Titen Turbo™ 3/16" x 2-1/4" Hex Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of...
The Simpson Strong-Tie TNT18214H Titen Turbo™ 3/16" x 2-1/4" Hex Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping and...
The Simpson Strong-Tie Outdoor Accents® hex-head washer provides the decorative appearance of a bolt connection. Its patent-pending design enables much easier installation than through-bolting....
The Simpson Strong-Tie Outdoor Accents® hex-head washer provides the decorative appearance of a bolt connection. Its patent-pending design enables much easier installation than through-bolting. The washer is code listed (IAPMO) and is designed exclusively to help fasten Outdoor Accents post bases, T and L straps, and angles using SDWS22312DBB and SDWS22512DBB structural screws. Used with Outdoor Accents® connectors and Outdoor Accents structural wood screws (sold separately) Quik...
The Simpson Strong-Tie HCJTZ is a heavy concealed connector used to provide a secure connection between a large wood beam to a wood post with no visible hardware. It can be installed three ways:...
The Simpson Strong-Tie HCJTZ is a heavy concealed connector used to provide a secure connection between a large wood beam to a wood post with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie HCJTZ with 3/4" x 4-3/4" pins can be used with a minimum beam size of 5-1/8" x 15". Minimum Beam Size: 5-1/8" x 15" Material: 10 Gauge Finish:...
The Simpson Strong-Tie ABU66SS with Type 316L Stainless Steel Corrosion Resistance is an adjustable post base for nominal size 6 x 6 post offers moisture protection and a finished hardware...
The Simpson Strong-Tie ABU66SS with Type 316L Stainless Steel Corrosion Resistance is an adjustable post base for nominal size 6 x 6 post offers moisture protection and a finished hardware appearance. The ABU66SS features 1" standoff height above concrete floors which is code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Base Material: 12 Gauge Strap Material: 10 Gauge...
The Simpson Strong-Tie HU210TF is a hybrid 2 x 10 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing...
The Simpson Strong-Tie HU210TF is a hybrid 2 x 10 hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that allows the hanger to be securely attached to the member. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 9-1/8" (Height) x 2-1/4" (Seat Depth) x 2-7/16" (Top Flange) Fasteners: (12)...
The S/HD10S Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD10S is...
The S/HD10S Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD10S is designed to provide loads for high-load shearwalls, braced-wall panels and lateral applications. The holdown features a unique seat that greatly minimizes deflection under load. The S/HD10S has been designed to utilize fewer fasteners and reduce installation time. Can be installed directly on the base...
The Simpson Strong-Tie PAB5-12 5/8" x 12" High Strength Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and...
The Simpson Strong-Tie PAB5-12 5/8" x 12" High Strength Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from high strength steel for higher load values. Please call our sales department direct at 800-323-2999 for pricing and...
The Simpson Strong-Tie MTS16Z ZMax® 1-1/4" Wide x 16" Long Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the...
The Simpson Strong-Tie MTS16Z ZMax® 1-1/4" Wide x 16" Long Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the rafter or heel of a truss. The MTS16 has a small bend section to reduce interference at the transition points between the two members. MTS straps do not need to be wrapped over the truss to achieve the allowable load. ZMax® coating provides corrosion resistance when required. Material: 16 gauge...
The Simpson Strong-Tie VTCR Single-Sided Valley Truss Clip provides a positive connection between the valley truss and the supporting framing below. Installed on top of the roof sheathing, it...
The Simpson Strong-Tie VTCR Single-Sided Valley Truss Clip provides a positive connection between the valley truss and the supporting framing below. Installed on top of the roof sheathing, it eliminates the need to add a support wedge under the valley truss or to bevel the bottom chord to match the roof pitch. Material: 18 Gauge Finish: Standard G90 Zinc Width: 2-1/2" Fasteners (Supporting Frame): (4) .148 x 3" Nails or (4) SD9212 Structural Screws Fasteners (Valley Truss): (3) .148 x 3" Nails...