Simpson Strong-Tie

Simpson Strong-Tie ECCO6 End Column Caps with no straps provides a high capacity connection between a 6x wide beam and a steel post. The ECCO6 End Column Caps comes with no coating to allow you to...

Simpson Strong-Tie ECCO6 End Column Caps with no straps provides a high capacity connection between a 6x wide beam and a steel post. The ECCO6 End Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 7 gauge Finish: No Coating Dimensions: 5-1/2" (Beam) x 7-1/2"...

The Simpson Strong Tie GH48-8 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if...

The Simpson Strong Tie GH48-8 Girder Hangers is used to connect a 4 x 8 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 5-5/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH48-8 Information and Installation Instructions. Gray Paint Coating Information Simpson Strong-Tie Gray Paint is a water-based paint...

The Simpson Strong-Tie® Strong-Drive® SDWS22800DB .220" x 8" wood screw is specifically designed for structural wood-to-wood applications and is also ideal for a wide variety of projects...

The Simpson Strong-Tie® Strong-Drive® SDWS22800DB .220" x 8" wood screw is specifically designed for structural wood-to-wood applications and is also ideal for a wide variety of projects where a high-strength attachment is needed. The 0.220" diameter of the SDWS22800DB 8" wood screw requires less torque to install than comparable fasteners, making it easier to drive. The Double-Barrier Coating corrosion-resistant coating makes it suitable for many interior and exterior applications....

The Simpson Strong-Tie® Strong-Drive® SDWH191000DB 10" screw is ideal for structural and general-purpose fastening applications where a hex-head drive is preferred. This 0.195" diameter...

The Simpson Strong-Tie® Strong-Drive® SDWH191000DB 10" screw is ideal for structural and general-purpose fastening applications where a hex-head drive is preferred. This 0.195" diameter fastener requires less torque to install than comparable fasteners, making it easier to drive; while the corrosion-resistant coating makes it suitable for many interior and exterior applications. The large hex washer head of the SDWH191000DB 10" screw creates an excellent bearing area for a secure...

Simpson Strong-Tie MASAPZ ZMaz®anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAPZ is not only quick to install they also...

Simpson Strong-Tie MASAPZ ZMaz®anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAPZ is not only quick to install they also eliminate the added cost of installing a bearing plate on the anchor bolt. This MASAPZ version is used for installation on panelized forms. This anchor featured ZMax® coating when additional corrosion resistance is needed. Attaches easily to the concrete form for quick installation Lays flat on the...

The Simpson Strong-Tie LTTI31 Light Tension Tie is designed to attach wood chord open wen trusses to concrete or masonry walls. The may also be installed vertically as long as they are attached to a...

The Simpson Strong-Tie LTTI31 Light Tension Tie is designed to attach wood chord open wen trusses to concrete or masonry walls. The may also be installed vertically as long as they are attached to a minimum 2 x 6 stud. If the base of the LTTI31 tie is flush with the concrete or masonry wall the allowable tension load increases (use link below for more information). Strap Material: 18 Gauge Plate Material: 3 Gauge Finish: Standard G90 Zinc Width: 3-3/4" Length: 31" Anchor Bolt: 5/8" Fastener...

The Simpson Strong-Tie HD12 Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown can obtain a wide...

The Simpson Strong-Tie HD12 Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown can obtain a wide variety of allowable tension loads depending on the thickness of the posts and the anchor bolt used. The HD12 must be connected to a minimum of 3-1/2" of material. Base Material: 3/8" Steel Body Material: 3 Gauge Steel Finish: Simpson Gray Paint Stud Bolts: (4) 1" Anchor Bolt Diameter: 1" or 1-1/8"...

Simpson Strong-Tie ECCQ46SDS2.5 End Column Caps provide a high capacity connection between a 4x beam and a 6x post. ECCQ46SDS2.5 End Column Caps should be used when the beam ends at the post. Each...

Simpson Strong-Tie ECCQ46SDS2.5 End Column Caps provide a high capacity connection between a 4x beam and a 6x post. ECCQ46SDS2.5 End Column Caps should be used when the beam ends at the post. Each ECCQ46SDS2.5 End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 5-1/2" (Post) x 8-1/2" (Length) Included Fasteners:...

The Simpson Strong-Tie 2-5/16" x 11-7/8" MIT3511.88 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed,...

The Simpson Strong-Tie 2-5/16" x 11-7/8" MIT3511.88 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90...

Simpson Strong Tie face mount HU11 Composite Lumber Hanger is designed for hanging 1-3/4" x 11-1/4 or 11-7/8" Microllam® LVL beams. Filling all holes including triangle holes will give you...

Simpson Strong Tie face mount HU11 Composite Lumber Hanger is designed for hanging 1-3/4" x 11-1/4 or 11-7/8" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load value. Material: 14 gauge Finish: Standard G90 Galvanized- Dimensions: 1-13/16" (Wide) x 11-1/16" (Height) x 2-1/2" (Seat Depth) Fastener Options: (22) 16d Nails (Header-Min) (6) 10d Nails (Joist-Min) (30) 16d Nails (Header-Max) (10) 10d Nails (Joist-Max) HU11 Information and Installation...

The Simpson Strong-Tie BC80 Half Base is an economical way to attach a nominal 8 x 8 post to a wood subfloor or bottom plate. Base Material: 18 Gauge Dimensions: (W) 7-1/2" x (L) 7-1/2" x (H) 3"...

The Simpson Strong-Tie BC80 Half Base is an economical way to attach a nominal 8 x 8 post to a wood subfloor or bottom plate. Base Material: 18 Gauge Dimensions: (W) 7-1/2" x (L) 7-1/2" x (H) 3" Finish: Standard G90 Zinc Fastener Options: (10) 16d Nails BC80 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low...

The Simpson Strong-Tie HD19 Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown can obtain a wide...

The Simpson Strong-Tie HD19 Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown can obtain a wide variety of allowable tension loads depending on the thickness of the posts and the anchor bolt used. The HD19 must be connected to a minimum of 5-1/2" of material. Base Material: 3/8" Steel Body Material: 3 Gauge Steel Finish: Simpson Gray Paint Stud Bolts: (5) 1" Anchor Bolt Diameter: 1-1/8" or...

Simpson Strong-Tie EPB66 allows you to install an elevated 6 x 6 post base from 1" to 2-1/2" above the concrete. This clearance allows the 6 x 6 post to stay above most standing water thus delaying...

Simpson Strong-Tie EPB66 allows you to install an elevated 6 x 6 post base from 1" to 2-1/2" above the concrete. This clearance allows the 6 x 6 post to stay above most standing water thus delaying any deterioration that will happen over time. EPB Post Bases do not provide enough resistance to stop a post from rotating so they should not be used in applications with no top connection such as fences and unbraced carports. Finish: Simpson Gray Paint Pipe Size: 1-1/16" OD x 8" Length Base Size:...

Head is Painted Sienna! The Simpson S11A237KJS 2-3/8" X .120" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted sienna to match siding or decking...

Head is Painted Sienna! The Simpson S11A237KJS 2-3/8" X .120" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted sienna to match siding or decking when applicable. The countersunk casing head with a checker pattern on the head helps the nail blend with the wood grain. The annular ring shank increases pull-out resistance thus decreasing chances of the nails backing out over time. Type 304 stainless steel Countersunk casing head Ring Shank shank...

Simpson Strong-Tie CCQ46SDS2.5 Column Caps provide a high capacity connection between a 4x beam and a 6x post. CCQ46SDS2.5 Column Caps should be used when the beam extends through the post. Each...

Simpson Strong-Tie CCQ46SDS2.5 Column Caps provide a high capacity connection between a 4x beam and a 6x post. CCQ46SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ46SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Stainless Steel as a special order. Please call our sales department direct at 800-323-2999 for...

Simpson Strong-Tie CCO6 End Column Caps with no post straps provides a high capacity connection between a 6x wide beam and a steel post. The CCO6 Column Caps comes with no coating to allow you to...

Simpson Strong-Tie CCO6 End Column Caps with no post straps provides a high capacity connection between a 6x wide beam and a steel post. The CCO6 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 7 gauge Finish: No Coating Dimensions: 5-1/2" (Beam) x 11"...

Simpson Strong-Tie ST6215 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of...

Simpson Strong-Tie ST6215 16-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of applications. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/16" (Wide) x 16-5/16" (Length) Fastener Options: (20) 16d Nails (20) SD10 x 1-1/2" Screws ST6215 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating...

Simpson Strong Tie HGUS3.25/10 3-1/8" Wide Glulam Hangers features double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12...

Simpson Strong Tie HGUS3.25/10 3-1/8" Wide Glulam Hangers features double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/4" (Wide) x 8-5/8" (Height) x 4" (Seat Depth) Fastener Options: (46) 16d Nails (Header) (16) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS3.25/10 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...

Simpson Strong-Tie IUS2.06/11.88 is used to install 2" x 11-7/8" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator...

Simpson Strong-Tie IUS2.06/11.88 is used to install 2" x 11-7/8" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/8" (Wide) x 11-7/8" (Height) x 2" (Seat Depth) Fastener Options : (10) .148 x 3" Nails (Face) IUS2.06/11.88 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating...

Simpson Strong-Tie ITS2.06/9.5 sets a new standard for engineered wood top flange hangers. The ITS2.06/9.5 installs 2" or 2-1/16" x 9-1/2" I-Joists faster and uses less nails than any other EWP top...

Simpson Strong-Tie ITS2.06/9.5 sets a new standard for engineered wood top flange hangers. The ITS2.06/9.5 installs 2" or 2-1/16" x 9-1/2" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Installing (4) 10d x 1-1/2" nails in...

Simpson Strong Tie LUS26-2 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows...

Simpson Strong Tie LUS26-2 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS26-2 Double 2 x 6 Hangers are also approved for installation with SD10 Structural Screws. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 4-7/8" (Height) x 2" (Seat...

Simpson Strong-Tie LU28 2 x 8 Joist Hangers are an economical and time saving solution to securely installing 2 x 8 joists to a wood ledger or beam. You can install LU28 hangers with with 10d or 16d...

Simpson Strong-Tie LU28 2 x 8 Joist Hangers are an economical and time saving solution to securely installing 2 x 8 joists to a wood ledger or beam. You can install LU28 hangers with with 10d or 16d nails depending on the load value you are trying to achieve. LU28 joist hangers are also approved for installation with Simpson Strong-Tie SD Structural Connector Screws. Material: 20 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 6-3/8" (Height) x 1-1/2" (Seat Depth) Fastener...

The Simpson Strong-Tie BC6 Post Caps allow you to create a light duty connection between a 6 x 6 nominal post and 6x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 5-1/2" (W) x...

The Simpson Strong-Tie BC6 Post Caps allow you to create a light duty connection between a 6 x 6 nominal post and 6x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 5-1/2" (W) x 5-1/2" (L) Fastener Options: (24) 16d BC6 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion...

Simpson Strong-Tie ECC5 1/4-6 End Column Caps provide a high capacity connection between a 5-1/8" Glulam beam and a 6x post. ECC5 1/4-6 End Column Caps should be used when the 5-1/8" beam ends at...

Simpson Strong-Tie ECC5 1/4-6 End Column Caps provide a high capacity connection between a 5-1/8" Glulam beam and a 6x post. ECC5 1/4-6 End Column Caps should be used when the 5-1/8" beam ends at the 6x post. Please Note: This column cap is also available in powder coat, Hot Dipped Galvanized and/or 90° rotated legs as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 5-1/4" (Beam) x 5-1/2"...