Simpson Strong-Tie

The Simpson Strong-Tie RSP4 Reversible Stud Plate Tie is designed to create a continuous load path to resist uplift. This versatile stud-plate tie is reversible and is able to connect a wood stud to...

The Simpson Strong-Tie RSP4 Reversible Stud Plate Tie is designed to create a continuous load path to resist uplift. This versatile stud-plate tie is reversible and is able to connect a wood stud to either a double top plate or a sill plate of a wood-framed wall. The RSP4 features locating tabs that aid in attaching the tie to the plates to ensure proper placement during installation. Embossments feature provides strength at the bend Designed to resist wind and seismic forces Material: 20...

Simpson Strong Tie HUC26-2Z ZMax® Double 2 x 6 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use...

Simpson Strong Tie HUC26-2Z ZMax® Double 2 x 6 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC26-2Z ZMax® hangers include additional triangle holes that can be used to increase load values when required. Reversed flanges allow you to hang hoist flush at corners or any other location where outside flanges will...

Simpson Strong-Tie Outdoor Accents® flat APT6 T-Straps bring decorative appeal and lateral strength to any outdoor living space like patio covers, gazebos and more. The APT6 T-Straps provide...

Simpson Strong-Tie Outdoor Accents® flat APT6 T-Straps bring decorative appeal and lateral strength to any outdoor living space like patio covers, gazebos and more. The APT6 T-Straps provide reinforcement for a connection where two 6x or larger lumber pieces intersect at a 90-degree angle in the center of the beam. These straps are easily installed with Outdoor Accents structural screws and hex-head washers. Install with Outdoor Accents® structural screws and hex-head washer (sold...

The Simpson Strong-Tie THD37300H6SS Type 316 Stainless Steel 3/8" x 3" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...

The Simpson Strong-Tie THD37300H6SS Type 316 Stainless Steel 3/8" x 3" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...

The Simpson Strong-Tie Mission Outdoor Accents APDMW56 decorative washer installs easily with the Outdoor Accents structural wood screw and hex-head washer and can be used in a variety of...

The Simpson Strong-Tie Mission Outdoor Accents APDMW56 decorative washer installs easily with the Outdoor Accents structural wood screw and hex-head washer and can be used in a variety of wood-to-wood connections. ZMax® galvanization with a black powder coat offers extra corrosion resistance for exterior and treated-wood applications Install with Outdoor Accents® structural wood screws and hex-head washers (sold separately) for a decorative look Material: 12 Gauge Steel Coating:...

The Simpson Strong-Tie DSVT4R5LB #10 x 4" Deck Drive™ Tan Wood Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start...

The Simpson Strong-Tie DSVT4R5LB #10 x 4" Deck Drive™ Tan Wood Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSV is ideally suited to be driven and countersunk into today’s wood deck boards. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth lumber. Also DSV screws are available in collated strips for use in the Quik Drive® auto-feed screw driving...

The Simpson Strong-Tie VPA4 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 3-1/2" wide rafters to the top plate. It will adjust to accommodate...

The Simpson Strong-Tie VPA4 Variable Pitch Connector may be sloped in the field, offering a versatile solution for attaching 3-1/2" wide rafters to the top plate. It will adjust to accommodate slopes between 3:12 and 12:12, making it a complement to the versatile LSSR Series Field-Adjustable Jack Hangers. This VPA series connectors eliminate the need for notched rafters, beveled top plates and toe nailing. Material: 18 Gauge Finish: Standard G90 Zinc Width: 3-9/16" Actual Joist Width: 3-1/2"...

The Simpson Strong-Tie TJC37 is a versatile connector for jack trusses. Adjustable from 0° to 85°, you can bend the TJC to the desired position (one bend cycle only). Each TJC is shipped...

The Simpson Strong-Tie TJC37 is a versatile connector for jack trusses. Adjustable from 0° to 85°, you can bend the TJC to the desired position (one bend cycle only). Each TJC is shipped with 67.5° bend. Nail hole locations allow for easy installation. No bevel cut is required. Minimum nailing option on TJC37 provides faster installation and lower installed cost. Material: 16 Gauge Finish: Standard G90 Zinc Width: 3-1/8" x 3-1/2" x 3-1/2" Fasteners (Minimum): (4) .131 x 1-1/2"...

The Simpson Strong-Tie ML26Z 12 Gauge angle combines strength and versatility through the use of Strong-Drive SDS25112 Heavy-Duty Connector screws. Fastener holes are staggered to minimize wood...

The Simpson Strong-Tie ML26Z 12 Gauge angle combines strength and versatility through the use of Strong-Drive SDS25112 Heavy-Duty Connector screws. Fastener holes are staggered to minimize wood splitting and opposing hole patterns allow for back-to-back installation without fastener interference. Please Note: SDS screws are not included. Finish: ZMax® coating Material: 12 Gauge Fasteners (Not Included): (8) SDS25112 Screws Dimensions: 6" Length x 2" (Flange Widths) ML26Z Information and...

Simpson Strong-Tie HL35PC Powder Coat Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL35PC to connect lumber to concrete...

Simpson Strong-Tie HL35PC Powder Coat Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL35PC to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Standard G90 Zinc Coating with a Black Powder Coat provides a low level of corrosion resistance. Please Note: This angle is available with a gusset as a special order.  Please call our sales department direct at 800-323-2999 for pricing and lead...

Simpson Strong-Tie ST2215 20-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of...

Simpson Strong-Tie ST2215 20-Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. ST series straps are designed to be used in a variety of applications. Material: 20 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/16" (Wide) x 16-5/16" (Length) Fastener Options: (20) 16d Nails (20) SD10 x 1-1/2" Screws ST2215 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating...

The Simpson Strong-Tie Quik Drive® WSV212S #9 x 2-1/2" Screws are ideal for screwing wood-to-wood when their is little concern about corrosion of the fasteners. The most common use of these...

The Simpson Strong-Tie Quik Drive® WSV212S #9 x 2-1/2" Screws are ideal for screwing wood-to-wood when their is little concern about corrosion of the fasteners. The most common use of these screws is for subfloor applications because the screw creates a very tight connection between the plywood and joist. Using a StrongDrive® Automatic Tool with a 20" extension saves time and labor thus saving you money. Redesigned tip and thread pattern provides easy starts and up to 25% less torque...

The Simpson S10A325CNJ 3-1/4" X .131" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head on this unpainted nail is a standard flat head. The checker pattern...

The Simpson S10A325CNJ 3-1/4" X .131" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head on this unpainted nail is a standard flat head. The checker pattern on the head helps the nail blend with the wood grain. The annular ring shank increases pull-out resistance thus decreasing chances of the nails backing out over time. Type 304 stainless steel Countersunk casing head Ring Shank shank 21º Collated Nails are designed to fit in the following tool. Please...

The Simpson Strong-Tie SSTB20 (5/8" Diameter by 21-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to...

The Simpson Strong-Tie SSTB20 (5/8" Diameter by 21-5/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 21-5/8" Minimum Embedment: 16-5/8" Finish: None Rolled threads for higher...

The Simpson Strong-Drive® SDS25212 1/4" x 2-1/2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25212 screw...

The Simpson Strong-Drive® SDS25212 1/4" x 2-1/2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25212 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 2-1/2" Thread Length: 1-1/2" Serrated Shank Diameter: 1/4" Point Type: Type 17 Point Drive...

The Simpson Strong-Tie LS70Z Skewable Reinforcing Angles with ZMax® Protection Coating are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS...

The Simpson Strong-Tie LS70Z Skewable Reinforcing Angles with ZMax® Protection Coating are field adjustable from 0° to 135°. These clips come standard with a 45° bend. The LS Skewable clips can only be bent one time. Flanges are 2-1/4" wide. LS70Z Angles can use 10d .148" x 1-1/2" or longer nails depending on the application. Material: 18 Gauge Finish: ZMax® Coating Length: 6-3/8" Flange Widths: 2-1/4" x 2-1/4" Fasteners: (10) 10d x 1-1/2" Nails LS70Z Information and...

The Simpson Strong-Tie L70 Reinforcing Angle is a 7" long framing clip used to create 90° wood to wood connections. The staggered nail pattern reduces the possibility of splitting the wood. The...

The Simpson Strong-Tie L70 Reinforcing Angle is a 7" long framing clip used to create 90° wood to wood connections. The staggered nail pattern reduces the possibility of splitting the wood. The flanges are 2-3/8" and 1-3/8" wide. The L70 angles can use 10d x 1-1/2" joist nail or #10 X 1-1/2" SD Structural Screws. Material: 16 Gauge Finish: Standard G90 Galvanizing Length: 7" Flange Widths: 1-3/8" x 2-3/8" Fasteners: (8) 10d x 1-1/2" Nails or (8) SD #10 x 1-1/2" Screws L70 Information and...

The Simpson PB46 Post Base for 4 x 6 (3-1/2" x 5-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed...

The Simpson PB46 Post Base for 4 x 6 (3-1/2" x 5-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Standard G90 Galvanized Embossed for greater strength Stress relief holes resist tearing Fasteners: (12) 16d Nails PB46 information and installation instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This...

The Simpson Strong-Tie ABU66Z with ZMax® Corrosion Resistance is an adjustable post base for nominal size 6 x 6 post offers moisture protection and a finished hardware appearance. The ABU66Z...

The Simpson Strong-Tie ABU66Z with ZMax® Corrosion Resistance is an adjustable post base for nominal size 6 x 6 post offers moisture protection and a finished hardware appearance. The ABU66Z features 1" standoff height above concrete floors which is code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Base Material: 12 Gauge Strap Material: 10 Gauge Dimensions: (W)...

The Simpson Strong-Tie BC46 Post Caps allow you to create a light duty connection between a 4 x 6 nominal post and 4x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 3-9/16" (W) x...

The Simpson Strong-Tie BC46 Post Caps allow you to create a light duty connection between a 4 x 6 nominal post and 4x nominal beam. Material: 18 Gauge Finish: Standard G90 Dimensions 3-9/16" (W) x 5-1/2" (L) Fastener Options: (18) 16d BC46 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion...

Simpson Strong-Tie ECCO5 1/4 End Column Caps with no straps provides a high capacity connection between a 5-1/8" wide beam and a steel post. The ECCO5 1/4 End Column Caps comes with no coating to...

Simpson Strong-Tie ECCO5 1/4 End Column Caps with no straps provides a high capacity connection between a 5-1/8" wide beam and a steel post. The ECCO5 1/4 End Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 3 gauge Finish: No Coating Dimensions: 5-1/4"...

Simpson Strong-Tie CC46 Column Caps provide a high capacity connection between a 4x wide beam and a 6x post. CC46 Column Caps should be used when the 4x beam extends through the 6x post. Please...

Simpson Strong-Tie CC46 Column Caps provide a high capacity connection between a 4x wide beam and a 6x post. CC46 Column Caps should be used when the 4x beam extends through the 6x post. Please Note: This column cap is also available in powder coat as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 3-5/8" (Beam) x 5-1/2" (Post) x 11" (Length) Fasteners: (4) 5/8" Machine Bolts (Beam) , (2) 5/8"...

Simpson Strong Tie HGUS28-2 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. HGUS26-2 hangers are...

Simpson Strong Tie HGUS28-2 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. HGUS26-2 hangers are designed to accept two 2 x 8 truss plates or joists with a minimum heel height of 6-9/16". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-5/16" (Wide) x 7-3/16" (Height) x 4" (Seat Depth) Fastener Options: (36) 16d Nails (Header) (12) 16d Nails (Joist)...Shorter Nails Not Allowed...

Simpson Strong-Tie ITS1.81/14 sets a new standard for engineered wood top flange hangers. The ITSITS1.81/14 installs 1-3/4" x 14" I-Joists faster and uses less nails than any other EWP top flange...

Simpson Strong-Tie ITS1.81/14 sets a new standard for engineered wood top flange hangers. The ITSITS1.81/14 installs 1-3/4" x 14" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Installing (4) 10d x 1-1/2" nails in the joist...