Simpson Strong-Tie

The Simpson Strong-Tie HD7B Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown uses the same design...

The Simpson Strong-Tie HD7B Holdown is a self jigging anchor that ensures the bottom bolt that attaches to the stud or post is seven times the diameter of the bolt. This holdown uses the same design as the HDQ8-SDS2.5 holdown that is proven to greatly reduce deflection while under load. All the HDB style holdown anchors are designed to provide loads for intermediate-load-range shearwalls, braced wall panels and lateral applications. The HD7B must be connected to a minimum of 3" of material....

The Simpson Strong-Tie ABW66Z for 6x6 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above concrete...

The Simpson Strong-Tie ABW66Z for 6x6 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above concrete floors, code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Additionally the ZMax® coating provides additional protection from exposure to the elements. The ABW66Z allows...

Simpson Strong-Tie MASAZ ZMax® anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAZ is not only quick to install they also...

Simpson Strong-Tie MASAZ ZMax® anchors are a labor saving solution to 1/2" and 5/8" standard anchor bolts for 2x, double-2x and 3x mudsills. The MASAZ is not only quick to install they also eliminate the added cost of installing a bearing plate on the anchor bolt. This MASAZ version is used for installation on standards forms. Attaches easily to the concrete form for quick installation Lays flat on the form board so there is no anchor bolt to finish around No labor costs involved in...

Simpson Strong-Tie 10DHDG-R 3" x .148" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 50 nails in the 1 lb. pack....

Simpson Strong-Tie 10DHDG-R 3" x .148" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 50 nails in the 1 lb. pack. The nails are hot dipped galvanized, providing medium corrosion protection. 10DHDG-R Information and Data Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average coating weight...

The Simpson Strong-Tie EPC8Z post cap is designed with the post and beam flanges in-line so that the EPC8Z end post cap can accommodate (3) 8x post sizes. The EPC8Z now uses easier-to-install 10d...

The Simpson Strong-Tie EPC8Z post cap is designed with the post and beam flanges in-line so that the EPC8Z end post cap can accommodate (3) 8x post sizes. The EPC8Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Please Note: This cap may be special ordered in a rough dimensional size as a manufactured...

Simpson Strong Tie face mount HU7 Composite Lumber Hanger is designed for hanging 1-3/4" x 7-1/4" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load...

Simpson Strong Tie face mount HU7 Composite Lumber Hanger is designed for hanging 1-3/4" x 7-1/4" Microllam® LVL beams. Filling all holes including triangle holes will give you maximum load value. Material: 14 gauge Finish: Standard G90 Galvanized- Dimensions: 1-13/16" (Wide) x 6-11/16" (Height) x 2-1/2" (Seat Depth) Fastener Options: (12) 16d Nails (Header-Min) (4) 10d Nails (Joist-Min) (16) 16d Nails (Header-Max) (8) 10d Nails (Joist-Max) HU7 Information and Installation Instructions....

The Simpson Strong-Tie PC8Z Center Post Cap is designed with the post and beam flanges in-line so that the PC8Z center post cap can accommodate (3) 8x post sizes. The PC8Z now uses easier-to-install...

The Simpson Strong-Tie PC8Z Center Post Cap is designed with the post and beam flanges in-line so that the PC8Z center post cap can accommodate (3) 8x post sizes. The PC8Z now uses easier-to-install 10d common nails saving you both time and labor. An alternate choice of fasteners is Strong-Drive® #9x1 1/2" SD Connector screws. Zmax® finish is standard to meet exposure conditions in many environments. Please Note: This cap may be special ordered in a rough dimensional size as a...

Simpson Strong-Tie 10D5HDG-R 3" x .148" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 250 nails in the 5 lb. pack....

Simpson Strong-Tie 10D5HDG-R 3" x .148" Hot Dipped Galvanized nails are mostly used used in angle clips and straps to reach the load values that are required. There are 250 nails in the 5 lb. pack. The nails are hot dipped galvanized, providing medium corrosion protection. 10D5HDG-R Information and Data Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average coating...

Simpson Strong Tie HUC26-2 Double 2 x 6 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...

Simpson Strong Tie HUC26-2 Double 2 x 6 Reversed Flange Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HUC26-2 hangers include additional triangle holes that can be used to increase load values when required. Reversed flanges allow you to hang hoist flush at corners or any other location where outside flanges will not work. Material:...

The Simpson Strong-Tie ABW66RZ for rough 6x6 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above...

The Simpson Strong-Tie ABW66RZ for rough 6x6 posts is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature 1" standoff height above concrete floors, code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Additionally the ZMax® coating provides additional protection from exposure to the elements. The ABW66RZ...

The geometry of the Simpson Strong-Tie SB1x30HDG Hot Dipped Galvanized 1" x 30" anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions the...

The geometry of the Simpson Strong-Tie SB1x30HDG Hot Dipped Galvanized 1" x 30" anchor bolt is the latest development in high capacity anchors. The smooth transition angle of the bolt positions the head of the anchor into an optimum position in the 8" wide concrete stem wall without creating excessive horizontal forces. The SB1x30HDG with a minimum embedment of 24" is intended to cover holdown devices that exceed the capacity of SSTB anchors. Identification on the bolt head showing embedment...

Simpson Strong-Tie HTU210-2 Double 2 x 10 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU210-2 hanger very versatile...

Simpson Strong-Tie HTU210-2 Double 2 x 10 Face Mount Hangers are designed so the nails line up with trusses with shallow heel heights as low as 3-7/8". This makes the HTU210-2 hanger very versatile for various trusses. Additionally you can have the HTU210-2 skewed up to a 67-1/2° angle. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2" max. to allow for greater construction tolerances (maximum gap for standard allowable loads is...

The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. Simpson Strong-Drive SD10112 #10 x 1-1/2"...

The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. Simpson Strong-Drive SD10112 #10 x 1-1/2" structural connector screws are approved to replace nails in certain Simpson Strong-Tie Connectors. The advantages of using screws can be ease of installation in tight spots and less vibration when installing connectors during remodel projects. The shank of the SD9112 screws are designed to easily fit...

Head is Painted Sienna! The Simpson Strong-Tie 2-1/4" x .092" Sienna Ring Shank Type 304 Stainless Steel Coil Nail is the best solution to protect your considerable investment in fine wood siding...

Head is Painted Sienna! The Simpson Strong-Tie 2-1/4" x .092" Sienna Ring Shank Type 304 Stainless Steel Coil Nail is the best solution to protect your considerable investment in fine wood siding from hard-to-remove stains and streaks with stainless steel wire coil nails. Chose from four colors or unpainted to match your siding. 3,600 nails per box Head Color - Sienna Type 304 stainless steel 15° collated angle Checker pattern on heads blends with wood grain, reduces glare from sunlight...

Simpson Strong-Tie LSTA24 20 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. LSTA series straps are designed to be used on the edge of 2x...

Simpson Strong-Tie LSTA24 20 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. LSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a LSTA strap that requires bending the strap can only be bent one time. Material: 20 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 24" (Length) Fasteners: (18) 10d Nails (18) SD9 x 1-1/2" Screws...

The Simpson Strong-Tie CJT5ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a...

The Simpson Strong-Tie CJT5ZL is a concealed connector to provide a secure wood to wood connection with no visible hardware. It can be installed three ways: with no routing of header/post or beam; a routed header/post, or a routed beam. The connection must be a 90° joint but may be sloped. The Simpson Strong-Tie CJT5ZL long (4-3/4") pins can be used with 5-1/8" Glulam Beams or 6x sawn lumber. Minimum Joist Size: Douglas Fir - 6 x 12 Glulam Beam - 5-1/8" x 10-1/2" Material: 12 Gauge Finish:...

Simpson Strong-Tie IUS1.81/16 is used to install 1-3/4" x 16" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator...

Simpson Strong-Tie IUS1.81/16 is used to install 1-3/4" x 16" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Filling the triangle holes in the flange will achieve maximum load values. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-7/8" (Wide) x 16" (Height) x 2" (Seat Depth) Fastener Options : (14) .148 x 3" Nails (Face-Min) (16) .148 x 3" Nails (Face-Max)...

Simpson Strong Tie HUS28 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows...

Simpson Strong Tie HUS28 2 x 8 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. HUS28 hangers are also approved for installation with SD10 x 2-1/2" Structural Screws. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-5/8" (Wide) x 7" (Height) x 3" (Seat Depth) Fastener...

Simpson Strong Tie HGUS28 2 x 8 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge...

Simpson Strong Tie HGUS28 2 x 8 Double Shear Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 1-5/8" (Wide) x 7-1/8" (Height) x 5" (Seat Depth) Fastener Options: (36) 16d Nails (Header) (12) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS28 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90...

Simpson Strong-Tie CCO4/6 End Column Caps with no post straps provides a high capacity connection between a 4x wide beam and a steel post. The CCO4/6 Column Caps comes with no coating to allow you...

Simpson Strong-Tie CCO4/6 End Column Caps with no post straps provides a high capacity connection between a 4x wide beam and a steel post. The CCO4/6 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 7 gauge Finish: No Coating Dimensions: 3-5/8" (Beam) x 11"...

Simpson Strong Tie LUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows...

Simpson Strong Tie LUS26 2 x 6 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. LUS26 hangers are also approved for installation with SD9 Structural Screws. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 4-3/4" (Height) x 1-3/4" (Seat Depth) Fastener...

Simpson Strong-Tie CCQ44SDS2.5 Column Caps provide a high capacity connection between a 4x beam and a 4x post. CCQ44SDS2.5 Column Caps should be used when the beam extends through the post. Each...

Simpson Strong-Tie CCQ44SDS2.5 Column Caps provide a high capacity connection between a 4x beam and a 4x post. CCQ44SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ44SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Stainless Steel as a special order. Please call our sales department direct at 800-323-2999 for...

The Simpson Strong-Tie BC60 Half Base is an economical way to attach a nominal 6 x 6 post to a wood subfloor or bottom plate. Base Material: 18 Gauge Dimensions: (W) 5-1/2" x (L) 5-1/2" x (H) 3"...

The Simpson Strong-Tie BC60 Half Base is an economical way to attach a nominal 6 x 6 post to a wood subfloor or bottom plate. Base Material: 18 Gauge Dimensions: (W) 5-1/2" x (L) 5-1/2" x (H) 3" Finish: Standard G90 Zinc Fastener Options: (10) 16d Nails (10) SD10 x 1-1/2" BC60 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating...

The Simpson AC6 Split Post Caps allow you to install the cap after the 6x post and 6x beam are set. Material: 18 Gauge Finish: Standard G90 Galvanized Dimensions 5-1/2" (W) x 8-1/2" (L) Fastener...

The Simpson AC6 Split Post Caps allow you to install the cap after the 6x post and 6x beam are set. Material: 18 Gauge Finish: Standard G90 Galvanized Dimensions 5-1/2" (W) x 8-1/2" (L) Fastener Options: Beam...(8) .162 x 3-1/2" Nails (Min) Beam...(14) .162 x 3-1/2" Nails (Max) Post...(8) .162 x 3-1/2" Nails (Min) Post...(14) .162 x 3-1/2" Nails (Max) Post and Beam...(28) SD10 x 1-1/2" (Max) AC6 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information...