Login/Register
Shopping Cart
OR
The Simpson Strong-Tie HTT4HDG Hot Dipped Galvanized Tension Tie have three fastener options to provide much higher load values than its HTT16 predecessor. Hot dipped galvanizing provides added...
The Simpson Strong-Tie HTT4HDG Hot Dipped Galvanized Tension Tie have three fastener options to provide much higher load values than its HTT16 predecessor. Hot dipped galvanizing provides added protection when install hardware to ACQ lumber. This tension tie may be installed up to 18" above the top of the concrete with no load reduction provided that additional elongation of the anchor rod is accounted for. HTT4HDG Tension Ties are designed to be used in both in vertical and horizontal...
The Simpson Strong-Tie 2-5/16" x 16" MIT3516 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is...
The Simpson Strong-Tie 2-5/16" x 16" MIT3516 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90...
The Simpson Strong-Tie 2-5/16" x 18" MIT3518 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is...
The Simpson Strong-Tie 2-5/16" x 18" MIT3518 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90 Galvanized...
The 1-1/4" wide x 18" long LTS18 Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist...
The 1-1/4" wide x 18" long LTS18 Simpson Strong-Tie twist straps are used to provide a tension connection between two wood members. They resist uplift at the heel of a truss economically. LTS twist straps have a 2" bend section that eliminates interference at the transition points between the two members. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 18" (Length) Fasteners: 10d or 10d x 1-1/2" depending on load value required and depth of receiving member (See...
Simpson Strong Drive® SSNA10D 1-1/2" x .148" Type 316 SSNA10D Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as...
Simpson Strong Drive® SSNA10D 1-1/2" x .148" Type 316 SSNA10D Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as well as protection from corrosive conditions. There are approximately 120 nails in the 1 lb. pack. The nails are type 316 stainless steel providing high/severe corrosion protection. SSNA10D Information and Data Type 316 Fastener Stainless Steel Information Type 316 stainless steel is a nickel...
Simpson Strong-Tie IUS2.06/16 is used to install 2" x 16" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs....
Simpson Strong-Tie IUS2.06/16 is used to install 2" x 16" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Filling the triangle holes in the flange will achieve maximum load values. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/8" (Wide) x 16" (Height) x 2" (Seat Depth) Fastener Options : (14) .148 x 3" Nails (Face-Min) (16) .148 x 3" Nails (Face-Max)...
The Simpson Strong-Tie Deck Drive™ DSVR212S #10 x 2-1/2" Red Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and...
The Simpson Strong-Tie Deck Drive™ DSVR212S #10 x 2-1/2" Red Collated Screw is a powerful fastening solution for preservative-treated decking applications. With its under-head nibs and fast-start tip, the DSVR212S is ideally suited to be driven using a PRO300S Quik Drive® Auto Feed Screw Gun. This screw is easily countersunk into today’s wood deck boards giving it a nice finished look. The shank is designed to withstand the swelling and shrinkage that is common with fast-growth...
Simpson Strong Tie HUS210-2 Double 2 x 10 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It...
Simpson Strong Tie HUS210-2 Double 2 x 10 Double Shear Joist Hangers have double-shear nailing. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation, and the use of standard nails for all connections. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 9-3/16" (Height) x 2" (Seat Depth) Fastener Options: (8) 16d Nails or SD10212 Screws (Header) (8) 16d Nails...
The Simpson Strong-Tie ABU88RHDG is an adjustable post base for rough size 8 x 8 post offers moisture protection and a finished hardware appearance. The ABU88RHDG features 1" standoff height above...
The Simpson Strong-Tie ABU88RHDG is an adjustable post base for rough size 8 x 8 post offers moisture protection and a finished hardware appearance. The ABU88RHDG features 1" standoff height above concrete floors which is code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. The Hot Dipped Galvanized feature provides an extra layer of protection from the elements. Base...
Head is Painted Tan! The Simpson S10A325KJT 3-1/4" X .131" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted tan to match siding or decking when...
Head is Painted Tan! The Simpson S10A325KJT 3-1/4" X .131" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted tan to match siding or decking when applicable. The countersunk casing head with a checker pattern on the head helps the nail blend with the wood grain. The annular ring shank increases pull-out resistance thus decreasing chances of the nails backing out over time. Type 304 stainless steel Countersunk casing head Ring Shank shank 21º...
Simpson Strong Tie HGUS48 4 x 8 Double Shear Beam Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge...
Simpson Strong Tie HGUS48 4 x 8 Double Shear Beam Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-5/8" (Wide) x 7-1/16" (Height) x 4" (Seat Depth) Fastener Options: (36) 16d Nails (Header) (12) 16d Nails (Joist)...Shorter Nails Not Allowed HGUS48 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard G90...
Simpson Strong-Tie CB66HDG Hot Dipped Galvanized column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB66HDG base is installed during the pouring of the...
Simpson Strong-Tie CB66HDG Hot Dipped Galvanized column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB66HDG base is installed during the pouring of the concrete. Strap Material: 7 Ga. x 3" Wide Hot Dipped Galvanized Steel Base Material: 7 Ga Hot Dipped Galvanized (5-1/2" x 5-1/2") Fasteners: (2) 5/8" Machine Bolts CB66HDG Information and Installation Instructions Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the...
Simpson Strong-Tie MSTA24 18 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x...
Simpson Strong-Tie MSTA24 18 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a MSTA strap that requires bending the strap can only be bent one time. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 24" (Length) Fasteners: (18) 10d Nails (18) SD9 x 1-1/2" Screws...
Simpson Strong-Tie CS14-R 14-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS14-R are approved for use with SD Screws as a nail...
Simpson Strong-Tie CS14-R 14-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS14-R are approved for use with SD Screws as a nail substitution. 25' packs are an economical choice when you do not require large amounts. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 1-1/4" (Wide) x 25' (Length) Fasteners: 8d or 10d depending on end length and material (See information link below) CS14-R Information and...
Simpson Strong-Tie CCO7 1/8 End Column Caps with no post straps provides a high capacity connection between a 7" wide beam and a steel post. The CCO7 1/8 Column Caps comes with no coating to allow...
Simpson Strong-Tie CCO7 1/8 End Column Caps with no post straps provides a high capacity connection between a 7" wide beam and a steel post. The CCO7 1/8 Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 3 gauge Finish: No Coating Dimensions: 7-1/8" (Beam) x...
Simpson Strong-Tie ECC66 End Column Caps provide a high capacity connection between a 6x beam and a 6x post. ECC66 End Column Caps should be used when the 6x beam ends at the 6x post. Please Note:...
Simpson Strong-Tie ECC66 End Column Caps provide a high capacity connection between a 6x beam and a 6x post. ECC66 End Column Caps should be used when the 6x beam ends at the 6x post. Please Note: This column cap is also available in powder coat, Hot Dipped Galvanized and/or 90° rotated legs as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 7 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 5-1/2" (Beam) x 5-1/2" (Post) x 7-1/2" (Length)...
Simpson Strong-Tie LU210 2 x 10 Joist Hangers are an economical and time saving solution to securely installing 2 x 10 joists to a wood ledger or beam. You can install LU210 hangers with with 10d or...
Simpson Strong-Tie LU210 2 x 10 Joist Hangers are an economical and time saving solution to securely installing 2 x 10 joists to a wood ledger or beam. You can install LU210 hangers with with 10d or 16d nails depending on the load value you are trying to achieve. LU210 joist hangers are also approved for installation with Simpson Strong-Tie SD Structural Connector Screws. LU210 Hangers can also be used with 2 x 12 and 2 x 14 joists when required. Material: 20 gauge Finish: Standard G90...
Simpson Strong-Tie ITS2.06/14 sets a new standard for engineered wood top flange hangers. The ITS2.06/14 installs 2" or 2-1/16" x 14" I-Joists faster and uses less nails than any other EWP top...
Simpson Strong-Tie ITS2.06/14 sets a new standard for engineered wood top flange hangers. The ITS2.06/14 installs 2" or 2-1/16" x 14" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Installing (4) 10d x 1-1/2" nails in the...
Simpson Strong Tie HU28-2 Double 2 x 8 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on...
Simpson Strong Tie HU28-2 Double 2 x 8 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. HU28-2 hangers include additional triangle holes that can be used to increase load values when required. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 7" (Height) x 2-1/2" (Seat Depth) Fastener...
Simpson Strong Tie U210-2 Double 2 x 10/12 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements....
Simpson Strong Tie U210-2 Double 2 x 10/12 Standard Face Mount Joist Hangers can use either 10d or 16d nails in the header allowing you to obtain multiple load values depending on your requirements. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 8-1/2" (Height) x 2" (Seat Depth) Fastener Options: (14) .162" x 3-1/2" 16d Nails (Header) (6) .148" x 3" 10d Nails (Joist) U210-2 Information and Installation Instructions. Standard G90 Zinc Galvanized Coating...
Simpson Strong Tie HUCQ410-SDS 3-9/16" Wide 4 x 10 Heavy Duty Joist Hangers come with the required SDS screws to reach the load values you require. HUCQ410-SDS hangers with concealed flanges are...
Simpson Strong Tie HUCQ410-SDS 3-9/16" Wide 4 x 10 Heavy Duty Joist Hangers come with the required SDS screws to reach the load values you require. HUCQ410-SDS hangers with concealed flanges are designed to use at the end of a beam or on a post with more width than the beam or joists. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Wide) x 9" (Height) x 3" (Seat Depth) Included Fasteners: (12) SDS 1/4" x 2-1/2" Screws (Header) (6) SDS 1/4" x 2-1/2" Screws (Joist)...
The Simpson Strong-Drive® SDS25312SS-R25 1/4" x 3-1/2" stainless steel structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood...
The Simpson Strong-Drive® SDS25312SS-R25 1/4" x 3-1/2" stainless steel structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25312SS-R25 stainless steel screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 3-1/2" Thread Length: 2-1/4" Serrated Shank...
The Simpson Strong-Tie THD37400CS 3/8" x 4" Titen HD heavy-duty screw anchor with countersunk head is part of a family of products that sets the standard for high-performance anchoring and ease of...
The Simpson Strong-Tie THD37400CS 3/8" x 4" Titen HD heavy-duty screw anchor with countersunk head is part of a family of products that sets the standard for high-performance anchoring and ease of installation. Designed for use in dry, interior, noncorrosive environments or temporary outdoor applications, the countersunk Titen HD offers industry-leading performance even in seismic conditions. The countersunk head style is for applications that require a flush-mount profile. Countersinking also...
The THD37500HMG Mechanical Galvanized 3/8" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD...
The THD37500HMG Mechanical Galvanized 3/8" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced...