Simpson Strong-Tie

The Simpson Strong-Tie SUR26-2 Skewed Right Double 2 x 6/8 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally...

The Simpson Strong-Tie SUR26-2 Skewed Right Double 2 x 6/8 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 6/8 joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 4-15/16" (Height) x 1-7/16" (Outside Flange) x 2-3/8" (Inside Flange) Fastener Options : (8) .162 x 3-1/2" 16d Nails (Face) (4)...

Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS2.06/11.88 sets a new standard for engineered wood top flange hangers. The ITS2.06/11.88 installs 2" or 2-1/16" x...

Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie ITS2.06/11.88 sets a new standard for engineered wood top flange hangers. The ITS2.06/11.88 installs 2" or 2-1/16" x 11-7/8" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses...

Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.06/14 is used to install 2" x 14" I-Joist when a top flange hanger in not required. Installation is fast and easy...

Save by Purchasing a Quantity of 30 Boxes (750 Pieces)! Simpson Strong-Tie IUS2.06/14 is used to install 2" x 14" I-Joist when a top flange hanger in not required. Installation is fast and easy using the Strong-Grip seat and self-jigging locator tabs. Joist nails are not required. Filling the triangle holes in the flange will achieve maximum load values. Material: 18 gauge Finish: Standard G90 Galvanized Dimensions: 2-1/8" (Wide) x 14" (Height) x 2" (Seat Depth) Fastener Options : (12) .148 x...

The Simpson Strong-Drive® SDS25312 1/4" x 3-1/2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25312 screw...

The Simpson Strong-Drive® SDS25312 1/4" x 3-1/2" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25312 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 3-1/2" Thread Length: 2-1/4" Serrated Shank Diameter: 1/4" Point Type: Type 17 Point Drive...

The S/HD15S Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD15S is...

The S/HD15S Simpson Strong-Tie holdowns are used as Cold Formed Steel framing connectors when structural steel members require a stud-to-foundation or floor to floor connection. The S/HD15S is designed to provide loads for high-load shearwalls, braced-wall panels and lateral applications. The holdown features a unique seat that greatly minimizes deflection under load. The S/HD15S has been designed to utilize fewer fasteners and reduce installation time. Can be installed directly on the base...

Head is Painted Tan! The Simpson S11A237KJT 2-3/8" X .120" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted tan to match siding or decking when...

Head is Painted Tan! The Simpson S11A237KJT 2-3/8" X .120" Stainless Strip Full Head Gun Nail is manufactured from Type 304 Stainless Steel. The head is painted tan to match siding or decking when applicable. The countersunk casing head with a checker pattern on the head helps the nail blend with the wood grain. The annular ring shank increases pull-out resistance thus decreasing chances of the nails backing out over time. Type 304 stainless steel Countersunk casing head Ring Shank shank 21º...

The Simpson Strong-Tie 2-5/16" x 16" MIT3516 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is...

The Simpson Strong-Tie 2-5/16" x 16" MIT3516 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90...

The Simpson Strong-Tie TNT18234H Titen Turbo™ 3/16" x 2-3/4" Hex Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of...

The Simpson Strong-Tie TNT18234H Titen Turbo™ 3/16" x 2-3/4" Hex Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping and...

Simpson Strong-Tie PDPAWL-287 Zinc Plated Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel PDPA pin...

Simpson Strong-Tie PDPAWL-287 Zinc Plated Pin is a powder-actuated washered pin designed to fasten building components to concrete, steel and CMU. The PDPAWL consists of a hardened-steel PDPA pin preassembled with a 1″ washer that provides additional bearing surface for enhanced upload resistance. Length: 2-7/8" Head Diameter: .300" Shank Diameter: .157" Coating: Standard G90 Zinc PDPAWL Series Fasteners Tension and Shear Loads in Normal Weight Concrete PAT Fastener MSDS Standard G90 Zinc...

The Simpson Strong-Tie H2AZ ZMax® Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H2AZ installation ties...

The Simpson Strong-Tie H2AZ ZMax® Clip is part of the Hurricane Tie System that features various configurations of wind and seismic ties for trusses and rafters. A typical H2AZ installation ties the rafter to the stud while spanning a top plate. The Simpson H2AZ requires (12) 8d x 1-1/2" joist nails. Material: 18 Gauge Finish: ZMax® G-185 Coating Fasteners: (12) 8d x 1-1/2" Nails H2AZ Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating...

The Simpson S15N200SFB 2" x 15ga. Angled Type 304 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The D-style...

The Simpson S15N200SFB 2" x 15ga. Angled Type 304 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The D-style head has greater bearing area to draw trim to the substrate. DA Style Finish Nails Fit the Following Tools: (Please check your owners manual regarding the proper lengths that your tool can use) Senco: FinishPro42XP, FinishPro41XP, FinishPro35, SFN40, SFN30, SFN1, SFN2B, SN1 Hitachi: NT64MA4...

Simpson Strong-Tie HL46 Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL46 to connect lumber to concrete using an a wedge...

Simpson Strong-Tie HL46 Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL46 to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Please Note: This angle is also available with a gusset or black powder coating as a special order.  Please call our sales department direct at 800-323-2999 for pricing and lead time. Material: 3 gauge Finish: Simpson Gray Paint Dimensions: 4-1/4" (W1) x 4-1/4"...

The Simpson Strong-Tie MASBZ ZMax® is a mudsill anchor designed specifically to anchor a mudsill to concrete block foundations or walls. The unique design eliminates problems associated with...

The Simpson Strong-Tie MASBZ ZMax® is a mudsill anchor designed specifically to anchor a mudsill to concrete block foundations or walls. The unique design eliminates problems associated with misplaced anchor bolts. The MASB easily installs into wet concrete-grouted CMU block for a time-saving alternative to anchor bolts. Offset design for use in concrete block applications One-piece design, so there are no nuts and washers to lose Unique design eliminates concerns about stud placement 16...

The THD37500H 3/8" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor...

The THD37500H 3/8" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques. The anchor...

Save by Purchasing a Quantity of 12 Boxes (72 Pieces)! Simpson Strong-Tie CB66 column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB66 base is installed...

Save by Purchasing a Quantity of 12 Boxes (72 Pieces)! Simpson Strong-Tie CB66 column bases are used to provide a connection of a 6 x 6 (5-1/2" x 5-1/2") post to concrete. The CB66 base is installed during the pouring of the concrete. Strap Material: 7 Ga. x 3" Wide Galvanized Steel Base Material: 7 Ga Galvanized (5-1/2" x 5-1/2") Fasteners: (2) 5/8" Machine Bolts CB66 Information and Installation Instructions Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized...

The Simpson CBSQ86-SDS2 (for 7-1/2" x 5-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post...

The Simpson CBSQ86-SDS2 (for 7-1/2" x 5-1/2" post) column bases include (12) 1/4" x 2" SDS screws for faster installation when compared to using machine bolts. The 1" standoff base keeps the post elevated above the concrete reducing the chance of rot from exposure to standing water. Easier Installation Higher Loads Standard G90 Galvanized Column Size: 8 x 6 Nominal (7-1/2" x 5-3/8") Base: 12 Ga. (7-1/2" x 5-3/8") Strap: 8 Ga. x 3" Wide x 8-11/16" High CBSQ86 Information and Installation...

Simpson Strong-Tie HDU8-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (20) 2-1/2" Simpson...

Simpson Strong-Tie HDU8-SDS2.5 Holdowns are pre-deflected during the manufacturing process, virtually eliminating deflection under load due to material stretch. They come with (20) 2-1/2" Simpson Strong-Tie® Strong-Drive® SDS screws which install easily and provide reduced fastener slip. Using SDS screws results in a greater net section, when compared to bolts, as no material is removed. Material: 10 Gauge Steel Finish: Standard G90 Galvanized Anchor Bolt Diameter: 7/8" Pre-deflected...

The Simpson Strong-Tie HTT4HDG Hot Dipped Galvanized Tension Tie have three fastener options to provide much higher load values than its HTT16 predecessor. Hot dipped galvanizing provides added...

The Simpson Strong-Tie HTT4HDG Hot Dipped Galvanized Tension Tie have three fastener options to provide much higher load values than its HTT16 predecessor. Hot dipped galvanizing provides added protection when install hardware to ACQ lumber. This tension tie may be installed up to 18" above the top of the concrete with no load reduction provided that additional elongation of the anchor rod is accounted for. HTT4HDG Tension Ties are designed to be used in both in vertical and horizontal...

The Simpson Strong-Tie ABU88RZ is an adjustable post base for rough size 8 x 8 post offers moisture protection and a finished hardware appearance. The ABU88RZ features 1" standoff height above...

The Simpson Strong-Tie ABU88RZ is an adjustable post base for rough size 8 x 8 post offers moisture protection and a finished hardware appearance. The ABU88RZ features 1" standoff height above concrete floors which is code-required when supporting permanent structures that are exposed to the weather or water splash, or in basements. They reduce the potential for decay at post and column ends. Base Material: 14 Gauge Strap Material: 12 Gauge Dimensions: (W) 8" x (L) 7" x (H) 7" Finish: ZMax...

The Simpson Strong-Tie L90Z Reinforcing Angle with ZMax® protection is a 9" long framing clip used to create 90° wood to wood connections. The staggered nail pattern reduces the possibility...

The Simpson Strong-Tie L90Z Reinforcing Angle with ZMax® protection is a 9" long framing clip used to create 90° wood to wood connections. The staggered nail pattern reduces the possibility of splitting the wood. The flanges are 2-3/8" and 1-3/8" wide. The L90Z angles can use 10d x 1-1/2" joist nail or #10 X 1-1/2" SD Structural Screws. Material: 16 Gauge Finish: ZMax® Coating Length: 9" Flange Widths: 1-3/8" x 2-3/8" Fasteners: (10) 10d x 1-1/2" Nails or (10) SD #10 x 1-1/2" L90Z...

The Simpson BC6Z ZMax® Post Caps allow you to create a light duty connection between a 6 x 6 nominal post and 6x nominal beam. ZMax® coating provide corrosion resistance when caps are...

The Simpson BC6Z ZMax® Post Caps allow you to create a light duty connection between a 6 x 6 nominal post and 6x nominal beam. ZMax® coating provide corrosion resistance when caps are installed in exposed locations. Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 5-1/2" (W) x 5-1/2" (L) Fastener Options: (24) 16d BC6Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a...

The Simpson Strong-Tie LCE4Z ZMax® Split Post Cap's universal design provides high capacity while eliminating the need for rights and lefts. For use with 4x or 6x lumber. LCE4Z Split Post Caps...

The Simpson Strong-Tie LCE4Z ZMax® Split Post Cap's universal design provides high capacity while eliminating the need for rights and lefts. For use with 4x or 6x lumber. LCE4Z Split Post Caps can be used as an end post cap application or an outside corner installation. ZMax® provides additional corrosion protection for applications that require it. Sold By The Each Material: 20 Gauge Finish: ZMax® G-185 Galvanized Fastener Options: (24) 16d (24) SD10 x 1-1/2" LCE4Z Information and...

Simpson Strong-Tie CC5 1/4-8 Column Caps provide a high capacity connection between a 5-1/8" GluLam beam and a 8x post. CC5 1/4-8 Column Caps should be used when the 5-1/8" beam extends through the...

Simpson Strong-Tie CC5 1/4-8 Column Caps provide a high capacity connection between a 5-1/8" GluLam beam and a 8x post. CC5 1/4-8 Column Caps should be used when the 5-1/8" beam extends through the 8x post. Please Note: This column cap is also available in powder coat or Hot Dipped Galvanized as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 5-1/4" (Beam) x 7-1/2" (Post) x 13" (Length)...

Simpson Strong-Tie ECCO7 1/8 End Column Caps with no straps provides a high capacity connection between a 7" wide beam and a steel post. The ECCO7 1/8 End Column Caps comes with no coating to allow...

Simpson Strong-Tie ECCO7 1/8 End Column Caps with no straps provides a high capacity connection between a 7" wide beam and a steel post. The ECCO7 1/8 End Column Caps comes with no coating to allow you to weld the cap either in the field or the shop. Please Note: This column cap may be ordered as Hot Dipped Galvanized. Please call our sales department direct at 800-323-2999 for more information including pricing and availability. Material: 3 gauge Finish: No Coating Dimensions: 7-1/8" (Beam) x...