Simpson Strong-Tie

The Simpson Strong-Tie MTS12Z ZMaz® 1-1/4" Wide x 12" Long Medium Twist Strap provides a tension connection between two members. This twist strap resists moderate uplift loads at the rafter or...

The Simpson Strong-Tie MTS12Z ZMaz® 1-1/4" Wide x 12" Long Medium Twist Strap provides a tension connection between two members. This twist strap resists moderate uplift loads at the rafter or heel of a truss. The MTS12 has a small bend section to reduce interference at the transition points between the two members. MTS straps do not need to be wrapped over the truss to achieve the allowable load. ZMax® coating provides corrosion resistance when required. Material: 16 gauge Finish:...

Save by Purchasing a Pallet of 16 Rolls! Simpson Strong-Tie CMST14 Coil Strap allows you to install 3" wide strapping at various lengths depending on your span requirements. CMST14 are approved for...

Save by Purchasing a Pallet of 16 Rolls! Simpson Strong-Tie CMST14 Coil Strap allows you to install 3" wide strapping at various lengths depending on your span requirements. CMST14 are approved for use with SD Screws as a nail substitution. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 3" (Wide) x 52-1/2' (Length) Fasteners: 10d or 16d depending on end length and material (See information link below) CMST14 Information and Installation Instructions. Standard G90 Zinc...

Save by Purchasing 72 Box Special! The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots...

Save by Purchasing 72 Box Special! The Simpson Strong-Tie DTC Double Slotted Roof Truss Clips are used for alignment control between a roof truss and nonbearing walls. The DTC has two 1-1/2" slots that will permit the truss chord to move vertically when loads are applied to the roof. The double slot increases the allowable load values. Material: 18 Gauge Finish: Standard G90 Zinc Fasteners: (6) 8d Nails DTC Information and Installation Instructions Standard G90 Zinc Galvanized Coating...

The Simpson Strong-Tie DSP Double Stud Plate Tie is a prebent strap designed to connect double studs to either top or bottom plates. This versatile double-stud-plate connector helps to create a...

The Simpson Strong-Tie DSP Double Stud Plate Tie is a prebent strap designed to connect double studs to either top or bottom plates. This versatile double-stud-plate connector helps to create a continuous load path in uplift resistance. The DSP features a top flange that allows the plate to attach securely to both sill plates and top plates. Embossments feature provides strength at the bend Can be installed before or after placement of wall Material: 18 Gauge Finish: Standard G90 Zinc Fastener...

The Simpson Strong-Tie A23Z ZMax® Framing Clips for various wood to wood connections at a 90° angle. ZMax® coating provides corrosion resistance when required. Material: 18 Gauge Finish:...

The Simpson Strong-Tie A23Z ZMax® Framing Clips for various wood to wood connections at a 90° angle. ZMax® coating provides corrosion resistance when required. Material: 18 Gauge Finish: ZMax® G-185 Coating Length: 2-3/4" Flange #1 (W1): 2" Flange #2 (W2): 1-1/2" Fasteners: (8) 10d x 1-1/2" Nails or(8) SD9112 Screws A23Z Information and Installation Instructions ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a G185...

The Simpson Strong-Tie DSC5L-SDS3HDG Hot Dipped Galvanized Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed...

The Simpson Strong-Tie DSC5L-SDS3HDG Hot Dipped Galvanized Left Drag-Strut Connector transfers the diaphragm shear forces from the girder truss or beam to the shearwalls. It is quickly installed using 3" SDS screws that are included with the connector. The DSC5L-SDS3 series drag strut connectors requires 40% less fasteners than the DSC4L connector but gets 12% higher loads. Material: 3 gauge Finish: Hot Dipped Galvanized Dimensions: 21" (Length) x 3" (Flanges) Included Fasteners: (24) SDS 1/4"...

The Simpson Strong-Tie RTA2Z ZMax® Rigid Tie® is designed to connect two 2x posts and joists at a 90° angle. This rigid tie angle fastens the members on two sides, eliminating the need for...

The Simpson Strong-Tie RTA2Z ZMax® Rigid Tie® is designed to connect two 2x posts and joists at a 90° angle. This rigid tie angle fastens the members on two sides, eliminating the need for angle bracing. Manufactured to high-quality standards to ensure solid performance, this rigid tie connector features a ZMax® galvanized finish for added corrosion resistance. Ideal for gates, fences or any project where a 90® connection is needed Fastens with #9 x 1-1/2" SD Screws (not...

Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! The Simpson Strong Tie GH46-8 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance...

Save by Purchasing a Quantity of 6 Boxes (90 Pieces)! The Simpson Strong Tie GH46-8 Girder Hangers is used to connect a 4 x 6 girder to a 8" foundation wall using 2x sill plate. 1-1/2" clearance hole can accommodate either rebar or an anchor bolt if required. Material: 12 gauge Finish: Simpson Strong-Tie Gray Paint: Low Dimensions: 3-9/16" (W) x 3-7/8" (H) x 8-1/16" (S) x 6" (L) Fasteners: (4) 16d Common Nails GH46-8 Information and Installation Instructions. Gray Paint Coating Information...

Simpson Strong Tie HGUS26-4 Quad Double Shear Face Mount Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require....

Simpson Strong Tie HGUS26-4 Quad Double Shear Face Mount Joist Hangers have double-shear nailing and 2-5/8" wide flanges that can accept enough 16d nails to reach the high loads you require. HGUS26-4 hangers are designed to accept four 2 x 6 truss plates or joists with a minimum heel height of 4-5/16". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 6-9/16" (Wide) x 5-7/16" (Height) x 4" (Seat Depth) Fastener Options: (20) 16d Nails (Header) (8) 16d Nails (Joist)...Shorter Nails...

The Simpson PB44HDG Hot Dipped Galvanized Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Hot...

The Simpson PB44HDG Hot Dipped Galvanized Post Base for 4 x 4 (3-1/2" x 3-1/2") dimensional lumber post is an economical method to connect a post to concrete prior to pouring the concrete. Hot Dipped Galvanized Embossed for greater strength Stress relief holes resist tearing Fasteners: (12) 16d Nails PB44HDG information and installation instructions Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with...

Simpson Strong-Tie CB44PC Powder Coat column bases are used to provide a connection of a 4 x 4 (3-1/2" x 3-1/2") post to concrete. The CB base is installed during the pouring of the concrete. This...

Simpson Strong-Tie CB44PC Powder Coat column bases are used to provide a connection of a 4 x 4 (3-1/2" x 3-1/2") post to concrete. The CB base is installed during the pouring of the concrete. This column base features a black powder-coat finish for a more decorative look. Strap Material: 7 Ga. x 2" Wide Black Powder Coat Steel Base Material: 7 Ga Black Powder Coat (3-9/16" x 3-9/16") Fasteners: (2) 5/8" Machine Bolts CB44PC Information and Installation Instructions Simpson Strong-Tie Powder...

The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. The Simpson Strong-Drive® SD9212SS SD...

The Simpson Strong-Tie Strong-Drive® SD and SDS structural-connector screws are the only screws approved for use with Simpson Strong-Tie connectors. The Simpson Strong-Drive® SD9212SS SD Stainless-Steel Connector Screw is specifically designed to replace nails in certain Simpson Strong-Tie® stainless-steel connectors. The load-rated SD9212SS screw has been tested and approved for use in many popular Simpson Strong-Tie products. In certain applications screws are easier and more...

The Simpson Strong-Tie Outdoor Accents® APRTC2 Decorative Rigid Corner Connector connects two horizontal members at a corner to a 2x vertical wood member. Manufactured to high-quality standards...

The Simpson Strong-Tie Outdoor Accents® APRTC2 Decorative Rigid Corner Connector connects two horizontal members at a corner to a 2x vertical wood member. Manufactured to high-quality standards to ensure solid performance, this corner Rigid Tie connector features ZMAX® galvanization with a black powder-coat finish for added corrosion resistance. As part of the Outdoor Accents Accessories line, this decorative hardware connector can be used with either the Mission Collection® or...

The Simpson Strong-Tie LSSR210Z Slopeable and Skewable Rafter Hanger allows you to install a nominal 2 x 10 rafter with either a plumb cut or miter cut that has been tacked in place. This versatile...

The Simpson Strong-Tie LSSR210Z Slopeable and Skewable Rafter Hanger allows you to install a nominal 2 x 10 rafter with either a plumb cut or miter cut that has been tacked in place. This versatile hanger is field adjustable for skewing up to 45° either left or right and features an innovative hinged swivel seat to adjust for up to a 45° slope. Material: 18 gauge Finish: ZMax® G-185 Coating Dimensions: 2-1/2" (Flange Width) x 9-1/8" (Height) x 1-9/16" (Joist Width) Fastener...

The Simpson Strong-Tie BC40SS Type 316L Stainless Steel Half Base is an easy way to attach a nominal 4 x 4 post to a wood subfloor or bottom plate. Type 316L Stainless Steel Corrosion Protection...

The Simpson Strong-Tie BC40SS Type 316L Stainless Steel Half Base is an easy way to attach a nominal 4 x 4 post to a wood subfloor or bottom plate. Type 316L Stainless Steel Corrosion Protection provides additional resistance to corrosive conditions. Base Material: 18 Gauge Dimensions: (W) 3-9/16" x (L) 3-1/4" x (H) 2-1/4" Finish: Type 316L Stainless Steel Fastener Options: (10) 16d Nails (10) SD10 x 1-1/2" BC40SS Information and Installation Instructions. Type 316L Connector Stainless Steel...

The Simpson Strong-Tie HU26-2TF is a hybrid 2 x 6-2 double hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features...

The Simpson Strong-Tie HU26-2TF is a hybrid 2 x 6-2 double hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty, top-flange joist hanger features face-nailing that allows the hanger to be securely attached to the member. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-1/8" (Wide) x 5-3/8" (Height) x 2-1/2" (Seat Depth) x 2-1/2" (Top...

The Simpson Strong-Tie TNT25114TF Titen Turbo™ 1/4" x 1-1/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the...

The Simpson Strong-Tie TNT25114TF Titen Turbo™ 1/4" x 1-1/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping...

Simpson Strong-Tie CCQ3-6SDS2.5 Column Caps provide a high capacity connection between a 3-1/8" beam and a 6x post. CCQ3-6SDS2.5 Column Caps should be used when the beam extends through the post....

Simpson Strong-Tie CCQ3-6SDS2.5 Column Caps provide a high capacity connection between a 3-1/8" beam and a 6x post. CCQ3-6SDS2.5 Column Caps should be used when the beam extends through the post. Each CCQ3-6SDS2.5 Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call our sales...

Simpson Strong-Tie CC44HDG Hot Dipped Galvanized Column Caps provide a high capacity connection between a 4x wide beam and a 4x post. CC44HDG Column Caps should be used when the 4x beam extends...

Simpson Strong-Tie CC44HDG Hot Dipped Galvanized Column Caps provide a high capacity connection between a 4x wide beam and a 4x post. CC44HDG Column Caps should be used when the 4x beam extends through the 4x post. Please Note: This column cap is also available in powder coat and/or 90° rotated legs as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 7 gauge Finish: Hot Dipped Galvanized Dimensions: 3-5/8" (Beam) x 3-5/8" (Post) x 7" (Length)...

The Simpson AC4SS Type 316L Stainless Steel Split Post Caps allow you to install the cap after the 4 x 4 post and 4x beam are set. Type 316L Stainless Steel protection provides additional corrosion...

The Simpson AC4SS Type 316L Stainless Steel Split Post Caps allow you to install the cap after the 4 x 4 post and 4x beam are set. Type 316L Stainless Steel protection provides additional corrosion resistance when application is in extreme corrosion situations. Material: 18 Gauge Finish: Type 316L Stainless Steel Dimensions 3-9/16" (W) x 6-1/2" (L) Fastener Options: Beam...(8) .162 x 3-1/2" Nails (Min) Beam...(14) .162 x 3-1/2" Nails (Max) Post...(8) .162 x 3-1/2" Nails (Min) Post...(14) .162...

The Simpson Strong-Tie ADT813S Epoxy Dispensing Tool features a steel carriage for ultimate durability. The ADT813S also features double-gripping plates that help extend tool life. This tool is...

The Simpson Strong-Tie ADT813S Epoxy Dispensing Tool features a steel carriage for ultimate durability. The ADT813S also features double-gripping plates that help extend tool life. This tool is designed for use with the Simpson AT-XP13 Epoxy Only. Please Note: You can also use the Simpson EDT22S Dispensing Tool to dispense Simpson AT-XP13 12.5oz. ACRYLIC-TIE Adhesive with a small modification. Explanation of "Stock" Availability Term Stock items are products we normally have available for...

Save by Purchasing a Quantity of 32 Boxes (800 Pieces)! Simpson Strong-Tie ITS1.81/9.5 sets a new standard for engineered wood top flange hangers. The ITSITS1.81/9.5 installs 1-3/4" x 9-1/2"...

Save by Purchasing a Quantity of 32 Boxes (800 Pieces)! Simpson Strong-Tie ITS1.81/9.5 sets a new standard for engineered wood top flange hangers. The ITSITS1.81/9.5 installs 1-3/4" x 9-1/2" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1...

Save by Purchasing a Quantity of 10 Boxes (500 Pieces)! Simpson Strong Tie HU26 2 x 4/6 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist...

Save by Purchasing a Quantity of 10 Boxes (500 Pieces)! Simpson Strong Tie HU26 2 x 4/6 Standard Face Mount Joist Hangers are heavy duty connectors with deeper seats than most other standard joist hangers. The hangers are designed for use on commercial properties and schools that require additional safety factors. Material: 14 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 3-1/16" (Height) x 2-1/4" (Seat Depth) Fasteners: (4) .162 x 3-1/2" (16d) Nails (Header) (2) .148 x...

The Simpson Strong-Tie HGAM10KTA Hurricane Gusset Angle is designed to secure the bottom chord of a gable end truss or other framing member to masonry. The engineered gusset in the angle increases...

The Simpson Strong-Tie HGAM10KTA Hurricane Gusset Angle is designed to secure the bottom chord of a gable end truss or other framing member to masonry. The engineered gusset in the angle increases strength for lateral and uplift loads. This hurricane gusset angle installs easily with 1 1/2" Strong-Drive® SDS Heavy-Duty Connector screws and Titen Turbo™ masonry screws to concrete or masonry. Each Kit Includes: (10) HGAM Hurricane Gusset Angles (40) 1/4" x 1-1/2" SDS Screws and (40)...