Simpson Strong-Tie

The Simpson Strong-Tie SUR210 Skewed Right 2 x 10/12 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate...

The Simpson Strong-Tie SUR210 Skewed Right 2 x 10/12 joist hangers are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 10/12 joist end may be square or beveled cut. Material: 16 gauge Finish: Standard G90 Galvanized Dimensions: 1-9/16" (Wide) x 8-1/8" (Height) x 1-1/8" (Outside Flange) x 1-5/16" (Inside Flange) Fastener Options : (10) .162 x 3-1/2" 16d Nails (Face) (10)...

The Simpson Strong-Tie SUR210Z Skewed Right 2 x 10/12 joist hangers with ZMax® coating are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will...

The Simpson Strong-Tie SUR210Z Skewed Right 2 x 10/12 joist hangers with ZMax® coating are skewed 45 degrees right. The angles nail slots direct nails for proper installation. These hangers will normally accommodate joists angles between 40-50 degrees. The 2 x 10/12 joist end may be square or beveled cut. ZMax coating provides additional corrosion protection when required. Material: 16 gauge Finish: ZMax® G-185 Galvanized Dimensions: 1-9/16" (Wide) x 8-1/8" (Height) x 1-1/8" (Outside...

Simpson Strong-Tie ITS2.37/11.88 sets a new standard for engineered wood top flange hangers. The ITS2.37/11.88 installs 2-5/16" x 11-7/8" I-Joists faster and uses less nails than any other EWP top...

Simpson Strong-Tie ITS2.37/11.88 sets a new standard for engineered wood top flange hangers. The ITS2.37/11.88 installs 2-5/16" x 11-7/8" I-Joists faster and uses less nails than any other EWP top flange hanger. The new Strong-Grip seat and Funnel Flange features allow standard joist installation without requiring joist nails resulting in the lowest installed cost. The Strong-Grip seat firmly secures I-joists with flange thicknesses from 1 1/8" to 1 1/2". Installing (4) 10d x 1-1/2" nails in...

The Simpson Strong-Tie 2-1/2" or 2-9/16" x 14" MIT314 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not...

The Simpson Strong-Tie 2-1/2" or 2-9/16" x 14" MIT314 I-Joist Hanger features Positive Angle Nailing (PAN) that is specifically designed for I-joists. With PAN, the nail hole material is not removed, but is formed to channel and confine the path of the nail at approximately 45°. PAN minimizes splitting of the flanges while permitting time-saving nailing from a better angle. Optional triangle nail holes may be used for increased uplift capacity. Material: 16 gauge Finish: Standard G90...

Simpson Strong-Tie MSTA36Z ZMax® 16 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of...

Simpson Strong-Tie MSTA36Z ZMax® 16 Gauge Straps are one of various strap ties that can transfer tension loads between two wood members. MSTA series straps are designed to be used on the edge of 2x material. The nailing pattern helps reduce the chances of the wood splitting. When using a MSTA strap that requires bending the strap can only be bent one time. Material: 16 gauge Finish: ZMax® G185 Galvanized Dimensions: 1-1/4" (Wide) x 36" (Length) Fasteners: (26) 10d Nails (26) SD9 x...

Simpson Strong-Tie CS16Z ZMax® 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16Z are approved for use with SD Screws...

Simpson Strong-Tie CS16Z ZMax® 16-Gauge Coil Strap allows you to install 1-1/4" wide strapping at various lengths depending on your span requirements. CS16Z are approved for use with SD Screws as a nail substitution. ZMax® coating allows you to install strapping in exterior applications. Material: 16 gauge Finish: ZMax® Coating Dimensions: 1-1/4" (Wide) x 150' (Length) Fasteners: 8d or 10d depending on end length and material (See information link below) CS16Z Information and...

The Simpson Strong-Tie MTS20Z ZMax® 1-1/4" Wide x 20" Long Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the...

The Simpson Strong-Tie MTS20Z ZMax® 1-1/4" Wide x 20" Long Medium Twist Strap provides a tension connection between two members. This economical twist strap resists moderate uplift loads at the rafter or heel of a truss. The MTS20 has a small bend section to reduce interference at the transition points between the two members. MTS straps do not need to be wrapped over the truss to achieve the allowable load. ZMax® coating provides additional corrosion resistance when required....

Simpson Strong-Tie H6Z Hurricane Tie with ZMax® Corrosion Protective Coating are designed to provide a connection from the stud to either the top plate or band (rim) joist. The H6Z Tie requires...

Simpson Strong-Tie H6Z Hurricane Tie with ZMax® Corrosion Protective Coating are designed to provide a connection from the stud to either the top plate or band (rim) joist. The H6Z Tie requires (16) 8d .131" x 1-1/2" or longer joist nails. Material: 16 Gauge Finish: ZMax® G-185 Coating Fastener Options: (16) 8d x 1-1/2" Nails H6Z Information and Installation Instructions. ZMax® Galvanized Coating Information ZMax® Coating is a thicker coating (galvanized per ASTM A653 with a...

The THD50400H 1/2" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor...

The THD50400H 1/2" x 4" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at significantly reduced installation torques. The anchor...

The Simpson S15N250SFN 2-1/2" x 15ga. Angled Type 304 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The...

The Simpson S15N250SFN 2-1/2" x 15ga. Angled Type 304 Stainless Steel Finish Nails should be used in exterior applications where highly corrosive conditions exist like seaside envoronments. The D-style head has greater bearing area to draw trim to the substrate. DA Style Finish Nails Fit the Following Tools: (Please check your owners manual regarding the proper lengths that your tool can use) Senco: FinishPro42XP, FinishPro41XP, FinishPro35, SFN40, SFN30, SFN1, SFN2B, SN1...

Simpson Strong-Tie HL55 Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL55 to connect lumber to concrete using an a wedge...

Simpson Strong-Tie HL55 Heavy Angles can be used for connecting lumber at a 90° angle using either through bolts or lags. You can also use the HL55 to connect lumber to concrete using an a wedge anchor or Titen Screw Bolt. Material: 7 gauge Finish: Standard G90 Galvanized-Level of Corrosion Resistance: Low Dimensions: 5-3/4" (W1) x 5-3/4" (W2) x 5" (L) Bolt Holes: (8) 1/2" HL55 Heavy Angle Information and Installation Instructions. Standard G90 Zinc Galvanized Coating Information Standard...

Simpson Strong-Tie Avant Outdoor Accents® APVB88DSP decorative side plates attach to the bottom of a 8 x 8 post or column installed with the APVB88 or APVB88R post base. These plates provide a...

Simpson Strong-Tie Avant Outdoor Accents® APVB88DSP decorative side plates attach to the bottom of a 8 x 8 post or column installed with the APVB88 or APVB88R post base. These plates provide a finished look to an installed post base. These decorative side plates provide a black powder coat finish over ZMax® galvanization for extra corrosion resistance. Install these side plates with Outdoor Accents® SDWS22312DBB structural wood screws and STN22 hex-head washers (sold separately)...

The Simpson Strong-Drive® SDS25600 1/4" x 6" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25600 screw...

The Simpson Strong-Drive® SDS25600 1/4" x 6" structural screw is a 1/4" diameter wood screw ideal for various connector installations as well as wood-to-wood applications. The SDS25600 screw installs with no pre-drilling and has been extensively tested in various applications. SDS screws feature a patented new easy driving 4CUT tip and a corrosion resistant double-barrier coating. Overall Length: 6" Thread Length: 3-1/4" Serrated Shank Diameter: 1/4" Point Type: Type 17 Point Drive Type:...

The Simpson Strong-Tie THD50500H6SS Type 316 Stainless Steel 1/2" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion...

The Simpson Strong-Tie THD50500H6SS Type 316 Stainless Steel 1/2" x 5" Titen HD is a patented, high-strength screw anchor for concrete and masonry. The self-undercutting, non-expansion characteristics of the Titen HD makes it the ideal anchor for structural applications, even at minimum edge distances and under reduced spacing conditions. The proprietary cutting teeth enable the Titen HD to be installed in one eighth of the time when compared to traditional expansion anchors, and at...

The Simpson Strong-Tie TNT25314TF Titen Turbo™ 1/4" x 3-1/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the...

The Simpson Strong-Tie TNT25314TF Titen Turbo™ 1/4" x 3-1/4" 6-Lobe Flat Head Screw Anchor is fast and easy to install, and incredibly reliable in its performance. The secret behind the performance of the Titen Turbo™ lies in a thread design that lowers driving torque while providing superior holding power. The revolutionary Torque Reduction Channel between the threads gives drilling dust a place to go, thereby significantly reducing torque-related issues like binding, stripping...

The Simpson Strong-Tie PAB5-30-HDG 5/8" x 30" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems...

The Simpson Strong-Tie PAB5-30-HDG 5/8" x 30" Hot Dipped Galvanized Pre-Assembled anchor bolt is a versatile cast-in-place anchor bolt ideal for high-tension-load applications, such as rod systems and shearwalls. It features a plate washer at the embedded end sandwiched between two fixed hex nuts and a head stamp for easy identification after the pour. This bolt is manufactured from standard steel but is available as a special order in high strength steel. Please call our sales department...

The Simpson Strong-Tie SSTB24LHDG Hot Dipped Galvanized (5/8" Diameter by 28-1/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB...

The Simpson Strong-Tie SSTB24LHDG Hot Dipped Galvanized (5/8" Diameter by 28-1/8") is designed for maximum performance as an anchor bolt for holdowns and Strong-Wall shearwalls. Extensive SSTB testing has been done to determine the design load capacity at a common application, the garage stem wall. Design loads are based on a series of five tests, with a three-times reduction factor. Minimum Stemwall Width: 6" Bolt Diameter: 5/8" Overall Length: 28-1/8" Minimum Embedment: 20-5/8" Finish: Hot...

Simpson Strong Drive® SSA16D 3-1/2" x .162" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as...

Simpson Strong Drive® SSA16D 3-1/2" x .162" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as well as protection from corrosive conditions. There are approximately 44 nails in the 1 lb. pack. The nails are type 316 stainless steel providing high/severe corrosion protection. SSA16D Information and Data Type 316 Fastener Stainless Steel Information Type 316 stainless steel is a nickel...

Simpson Strong Drive® SSA16D5 3-1/2" x .162" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required...

Simpson Strong Drive® SSA16D5 3-1/2" x .162" Type 316 Ring Shank Stainless Steel nails are mostly used used in stainless steel angle clips and straps to reach the load values that are required as well as protection from corrosive conditions. There are approximately 200 nails in the 5 lb. pack. The nails are type 316 stainless steel providing high/severe corrosion protection. SSA16D Information and Data Type 316 Fastener Stainless Steel Information Type 316 stainless steel is a nickel...

The Simpson Strong-Tie BCS2-3/6Z ZMax® allows for the connection of (3) 2x's to a 6x post. Double-shear nailing between beam and post gives added strength. The BC/BCS series offers dual-purpose...

The Simpson Strong-Tie BCS2-3/6Z ZMax® allows for the connection of (3) 2x's to a 6x post. Double-shear nailing between beam and post gives added strength. The BC/BCS series offers dual-purpose post cap/base for light cap or base connections. Install dome nails on beam; drive nails at an angle through the beam into the post below to achieve the table loads Material: 18 Gauge Finish: ZMax® G-185 Coating Dimensions 5-9/16" (Post Width) x 4-5/8" (Joists Width) Fastener Options: (18) 16d...

Simpson Strong-Tie ECCQ5-8SDS2.5 End Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 8x post. ECCQ5-8SDS2.5 End Column Caps should be used when the beam ends at the...

Simpson Strong-Tie ECCQ5-8SDS2.5 End Column Caps provide a high capacity connection between a 5-1/8" Glulam Beam and a 8x post. ECCQ5-8SDS2.5 End Column Caps should be used when the beam ends at the post. Each ECCQ5-8SDS2.5 End Column Cap includes the required SDS screws that will allow you to install the cap faster as well making them lower profile than caps with bolts. Please Note: This column cap may be available in Hot Dipped Galvanized or Stainless Steel as a special order. Please call...

The Simpson Strong-Tie HTT5HDG Hot Dipped Galvanized Tension Tie has added protection for use in areas where corrosion maycause problems like ACQ lumber. This tension tie may be installed up to 18"...

The Simpson Strong-Tie HTT5HDG Hot Dipped Galvanized Tension Tie has added protection for use in areas where corrosion maycause problems like ACQ lumber. This tension tie may be installed up to 18" above the top of the concrete with no load reduction provided that additional elongation of the anchor rod is accounted for. Using a BP58-2 bearing plate installed in the seat of the HTT5 provides add more allowable tension load to the connection. HTT5 Tension Ties are designed to be used in both in...

Simpson Strong-Tie ECC76 End Column Caps provide a high capacity connection between a 6-3/4" Glulam beam and a 6x post. ECC76 End Column Caps should be used when the 6-3/4" beam ends at the 6x post....

Simpson Strong-Tie ECC76 End Column Caps provide a high capacity connection between a 6-3/4" Glulam beam and a 6x post. ECC76 End Column Caps should be used when the 6-3/4" beam ends at the 6x post. Please Note: This column cap is also available in powder coat, Hot Dipped Galvanized and/or 90° rotated legs as a special order. Please call 800-323-2999 for pricing and lead time for shipping. Material: 3 gauge Finish: Simpson Strong-Tie Gray Paint Dimensions: 6-7/8" (Beam) x 5-1/2" (Post) x...

The Simpson Strong-Tie HUC46TF is a hybrid 4 x 6 concealed flange hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty joist hanger is designed with two...

The Simpson Strong-Tie HUC46TF is a hybrid 4 x 6 concealed flange hanger that incorporates the advantages of both face-mount and top-mount hangers. This heavy-duty joist hanger is designed with two concealed flanges for end-of-wall or corner installation. The minimum header or ledger size that can be used with this hanger must be 3-1/2". Material: 12 gauge Finish: Standard G90 Galvanized Dimensions: 3-9/16" (Wide) x 5-3/8" (Height) x 2-1/2" (Seat Depth) x 2-1/2" (Top Flange) Fasteners: (10)...