Login/Register
Shopping Cart
OR
Filter
Sort By
7/8" - 9 Zinc Plated Hex Nuts for either 5/8" machine bolts or all thread rod. Uses 1-5/16" socket to install. Important: These zinc plated hex nuts will NOT work with Hot Dipped Galvanized bolts or...
7/8" - 9 Zinc Plated Hex Nuts for either 5/8" machine bolts or all thread rod. Uses 1-5/16" socket to install. Important: These zinc plated hex nuts will NOT work with Hot Dipped Galvanized bolts or threaded rod. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments. Level of Corrosion...
These 1/2" x 12" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary...
These 1/2" x 12" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and...
BPS58-3HDG Hot Dipped Galvanized Slotted Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. BPS bearing plates...
BPS58-3HDG Hot Dipped Galvanized Slotted Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. BPS bearing plates require you to use a 5/8" cut washer before installing the hex nut. These bearing plates are hot dipped galvanized to protect the washer from corrosion when exposed to the elements as well as coming in contact with ACQ lumber. Hole Size: Slotted for 5/8" Bolt Dimension: 3" x 3" Thickness: 1/4"...
These 5/8" x 36" zinc plated all thread rods when used with a 5/8" coupling nut can be used for extending machine bolts or any other 5/8" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated...
These 5/8" x 36" zinc plated all thread rods when used with a 5/8" coupling nut can be used for extending machine bolts or any other 5/8" plain or zinc plated treaded rod. A307 Grade 2 Zinc Plated Special lengths available upon request Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments....
7/8" - 9 Hot Dipped Galvanized Hex Nuts for either 7/8" HDG machine bolts or all thread rod. Uses 1-5/16" socket to install. Important: These HDG hex nuts will only fit hot galvanized bolts or...
7/8" - 9 Hot Dipped Galvanized Hex Nuts for either 7/8" HDG machine bolts or all thread rod. Uses 1-5/16" socket to install. Important: These HDG hex nuts will only fit hot galvanized bolts or threaded rod. Do NOT use on plain or zinc plated bolts. Hot Dipped Galvanized Coating Information Hot-Dip Galvanizing is applied after the products are fabricated. The coating weight increases with material thickness. The minimum average coating weight is 2.0 oz./ft2 (per ASTM A123 total both sides)....
7/8" USS Zinc Plated Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Zinc Plating provides minimum corrosion resistance and...
7/8" USS Zinc Plated Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Zinc Plating provides minimum corrosion resistance and should not be used with ACQ lumber. Bolt Size: 7/8" Inside Diameter: 15/16" Outside Diameter: 2-1/4" Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of...
Simpson Strong-Tie CNW7/8-5/8 coupling nuts are a tested and load rated method to join 7/8" threaded rod or anchor bolts to 5/8" rod extensions. The "witness" holes in the nut provide a means to...
Simpson Strong-Tie CNW7/8-5/8 coupling nuts are a tested and load rated method to join 7/8" threaded rod or anchor bolts to 5/8" rod extensions. The "witness" holes in the nut provide a means to visually verify when rods are properly installed. The positive stop feature helps ensure even threading into each end of the nut. CNW7/8-5/8 meet and exceed the capacity of corresponding ASTM A36 bolts and threaded rod. CNW7/8-5/8 Information and Data Standard G90 Zinc Galvanized Coating Information...
These 5/8" x 36" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as...
These 5/8" x 36" hot dipped galvanized all thread rods when used with a 5/8" HDG coupling nut can be used for extending HDG machine bolts and HDG all thread rod. They can also sometimes be used as an anchor bolt substitution (Consult your structural engineer first). Hot dipped galvanizing provides extra protection when contacting ACQ lumber. Please Note: This all thread is cut in our own shop. Bare ends are painted with galvanizing spray paint. A307 Grade 2 Hot Dipped Galvanized Special...
These 5/8" x 4" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length...
These 5/8" x 4" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments. Level of...
Simpson Strong-Tie CNW7/8-7/8-OST coupling nuts are a tested and load rated method to join 7/8" Hot Dipped Galvanized threaded rod or anchor bolts to 7/8" standard rod extensions. The "witness"...
Simpson Strong-Tie CNW7/8-7/8-OST coupling nuts are a tested and load rated method to join 7/8" Hot Dipped Galvanized threaded rod or anchor bolts to 7/8" standard rod extensions. The "witness" holes in the nut provide a means to visually verify when rods are properly installed. The positive stop feature helps ensure even threading into each end of the nut. CNW7/8-7/8-OST meet and exceed the capacity of corresponding ASTM A36 bolts and threaded rod. CNW7/8-7/8-OST Information and Data Standard...
1" - 1 Zinc Plated Hex Nuts for either 1" machine bolts or all thread rod. Uses 1-1/2" socket to install. Important: These zinc plated hex nuts will NOT work with Hot Dipped Galvanized bolts or...
1" - 1 Zinc Plated Hex Nuts for either 1" machine bolts or all thread rod. Uses 1-1/2" socket to install. Important: These zinc plated hex nuts will NOT work with Hot Dipped Galvanized bolts or threaded rod. Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments. Level of Corrosion...
1" USS Zinc Plated Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Zinc Plating provides minimum corrosion resistance and should...
1" USS Zinc Plated Flat Washers are used to prevent the bolt head and/or hex nut from embedding into the wood surface during tightening. Zinc Plating provides minimum corrosion resistance and should not be used with ACQ lumber. Bolt Size: 1" Inside Diameter: 1-1/16" Outside Diameter: 2-1/2" Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of...
These 5/8" x 5" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length...
These 5/8" x 5" hex head plated machine bolts can be used for various wood-to-wood and/or metal-to-wood connection. Grade 2 ASTM A307 Zinc Plated Hex Head Uses 15/16" Socket Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in dry environments. Level of...
1" x 2-11/16" (H) Witness Hole Coupling Nuts are used to connected two 1" threaded rods together or extend a 1" SB and standard anchor bolt. The witness hole allows the inspector to confirm the rods...
1" x 2-11/16" (H) Witness Hole Coupling Nuts are used to connected two 1" threaded rods together or extend a 1" SB and standard anchor bolt. The witness hole allows the inspector to confirm the rods are connected properly. Zinc Plated Hex Head Imported Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance and should be used in...
BP34-2HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot...
BP34-2HDG Hot Dipped Galvanized Square Bearing Plates give greater bearing surface than standard cut washers, and help distribute the load at these critical connections. These bearing plates are hot dipped galvanized to protect the washer from corrosion when exposed to the elements as well as coming in contact with ACQ lumber. Hole Size: 13/16" Dimension: 2" x 2" Thickness: 3/16" Coating: Hot Dipped Galvanized Mild Steel Imported Picture may not match product exactly Hot Dipped Galvanized...
These 5/8" x 2-1/2" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary...
These 5/8" x 2-1/2" plated lag screws can be used for fastening metal-to-wood or wood-to-wood applications. Pre-drilling is required. Length is measured from the bottom of the hex head and may vary slightly. Zinc Plated Hex Head Imported Thread Length May Not Match Picture Standard G90 Zinc Galvanized Coating Information Standard G90 Zinc Galvanized Coating contains 0.90 oz. of zinc per square foot of surface area (total both sides). This coating provides a low level of corrosion resistance...